參數資料
型號： A49FL004TL-33F
廠商： AMIC Technology Corporation
英文描述： 4 Mbit CMOS 3.3Volt-only Firmware Hub/LPC Flash Memory
中文描述： 4兆位的CMOS 3.3Volt只固件集線器/ LPC快閃記憶體
文件頁數： 16/36頁
文件大?。?/td> 713K
代理商： A49FL004TL-33F
A49FL004
PRELIMINARY (September, 2005, Version 0.0)
15
AMIC Technology, Corp.
ADDRESS/ADDRESS MULTIPLEXED (A/A
MUX) MODE
Read/Write Operation
The A49FL004 offers a Address/Address Multiplexed (A/A
Mux) mode for off-system operation, typically on an EPROM
Programmer, similar to a traditional Flash memory except the
address input is multiplexed. In the A/A Mux mode, the
programmer must drive the OE pin to low (V
IL
) for read or
WE
pins to low for write operation. The devices have no
Chip Enable ( CE ) pin for chip selection and activation as
traditional Flash memory. The
used to activate the device and control the power.
C
R/
, OE and
WE
pins are
The 11 multiplex address pins - A[10:0] and a
used to load the row and column addresses for the target
memory location. The row addresses (internal address A10 -
A0) are latched on the falling edge of
addresses (internal address A21 - A11) are latched on the
rising edge of
C
R/
pin. The A49FL004 use A18 - A0
respectively.
During a read operation, the OE signal is used to control the
output of data to the 8 I/O pins - I/O[7:0]. During a write
operation, the
WE
signal is used to latch the input data from
I/O[7:0]. See Table 11 for Bus Operation Modes.
C
R/
pin are
C
R/
pin. The column
Table 11: A/A Mux Mode Operation Selection
Notes:
1. X can be V
IL
OR V
IH
.
2. Refer to Table 12 for the Manufacturer ID and Device ID of devices.
The A49FL004 provides three levels of data protection for
the critical BIOS code of PC and Notebook. It includes
memory hardware write protection, hardware data protection
and software data protection.
Sector-Erase Operation
The A49FL004 contains 128 uniform 4 KByte sectors. A
sector erase command is used to erase an individual sector.
See Table 11 for Sector/Block Address Table.
In FWH/LPC mode, an erase operation is activated by writing
the six-byte command sequence through six consecutive
write memory cycles with Sector Erase Command (30h), and
sector address (SA) in the last bus cycle.
In A/A Mux mode, an erase operation is activated by writing
the six-byte command in six consecutive bus cycles. Pre-
programs the sector is not required prior to an erase
operation.
Block-Erase Operation
The A49FL004 contains eight uniform 64 KByte blocks. A
block erase command is used to erase an individual block.
See Table 13 for Sector/Block Address Table.
In FWH/LPC mode, an erase operation is activated by writing
the six-byte command sequence through six consecutive
write memory cycles with Block Erase Command (50h), and
Block address (BA) in the last bus cycle.
In A/A Mux mode, an erase operation is activated by writing
the six-byte command in six consecutive bus cycles. Pre-
programs the block is not required prior to an erase operation.
Chip-Erase
The entire memory array can be erased by chip erase
operation available under the A/A Mux mode operated by
EPROM Programmer only. Pre-programs the device is not
required prior to the chip erase operation. Chip erase starts
immediately after a six-bus-cycle chip erase command
sequence. All commands will be ignored once the chip erase
operation has started. The
Data
Polling on I/O
7
or Toggle Bit
on I/O
6
can be used to detect the progress or completion of
erase operation. The device will return back to standby mode
after the completion of the chip erase.
Write Operation Status Detection
In program operation, the data is programmed into the
devices (to a logical “0”) on a byte-by-byte basis. In FWH and
LPC mode, a program operation is activated by writing the
three-byte command sequence and program address/data
Mode
RST
OE
WE
Address
I/O
Read
V
IH
V
IL
V
IH
X
(1)
D
OUT
Write
V
IH
V
IH
V
IL
X
D
IN
Standby
V
IH
V
IH
V
IH
X
High Z
Output Disable
V
IH
V
IH
X
X
High Z
Reset
V
IL
X
X
X
High Z
A2 – A21 = X, A1 = V
IL
, A0 = V
IL
,
and A1 = V
IH
, A0 = V
IH
Manufacturer ID
(2)
Product Identification
V
IH
V
IL
V
IH
A2 – A21= X, A1 = V
IL
, A0 = V
IH
Device ID
相關PDF資料
PDF描述
A49FL004TX-33 4 Mbit CMOS 3.3Volt-only Firmware Hub/LPC Flash Memory
A49LF004TX-33C 4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
A49LF004TL-33C 4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
A49LF004 4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
A49LF040A 4 Mbit CMOS 3.3Volt-only Low Pin Count Flash Memory
相關代理商/技術參數
參數描述
A49FL004TX-33 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Firmware Hub/LPC Flash Memory
A49FL004TX-33F 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Firmware Hub/LPC Flash Memory
A49LF004 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
A49LF004TL-33C 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
A49LF004TX-33C 制造商:AMICC 制造商全稱:AMIC Technology 功能描述:4 Mbit CMOS 3.3Volt-only Firmware Hub Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*