- 您現在的位置：買賣IC網 > PDF目錄375131 > A3054 (Allegro MicroSystems, Inc.) Multiplexed Two-Wire Hall Effect Sensor(多路復用2線霍爾效應傳感器) PDF資料下載
參數資料
| 型號： | A3054 |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Multiplexed Two-Wire Hall Effect Sensor(多路復用2線霍爾效應傳感器) |
| 中文描述： | 復用兩線霍爾效應傳感器（多路復用2線霍爾效應傳感器） |
| 文件頁數： | 4/12頁 |
| 文件大?。?/td> | 87K |
| 代理商： | A3054 |
3054
MULTIPLEXED
TWO-WIRE
HALL-EFFECT SENSOR ICs
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
A device may be addressed by changing the supply
voltage as shown in Figure 1. A preferred addressing
protocol is as follows: the bus supply voltage is brought
low (<2.5 V) so that all devices on the bus are reset. The
voltage is then raised to the address LOW voltage (V
L
) and
the bus quiescent current is measured. The bus is then
toggled between V
L
and V
H
(address HIGH voltage), with
each positive transition representing an increment in the
bus address. After each voltage transition, the bus current
may be monitored to check for diagnostic and signal
responses from sensor ICs.
Sensor Addressing
When a sensor detects a bus address equal to its
factory-programmed address, it responds with an increase
in its supply current drain ( I
S
) during the next HIGH portion
ADDRESSING PROTOCOL
Magnetic Operate Point (B
OP
)
Minimum magnetic field required to switch ON the
Hall amplifier and switching circuitry of the addressed
sensor. This circuitry is only active when the sensor is
addressed.
Magnetic Release Point (B
RP
)
Magnetic field required to switch OFF the Hall
amplifier and switching circuitry after the output has been
switched ON. When a device is deactivated by changing
the bus address, all magnetic memory is lost.
Magnetic Hysteresis (B
HYS
)
Difference between the B
OP
and B
RP
magnetic field
thresholds.
FIGURE 1
BUS TIMING
SAND SIGNAL CURRENTS
DIAGNOSTIC
DIAGNOSTIC
DIAGNOSTIC
DIAGNOSTIC
ADDRESS
n
RESET
ADDRESS 01
SENSOR 02 —
DIAGNOSTIC
SENSOR 01
VH
VL
VRST
0
IS
IQL
IQH
0
IS
0
IS
n IQL
n IQH
0
tphl
tplh
VCLH
VCHL
Dwg. WH-005
BUS
VOLTAGE
SENSOR 02
WITH NO
MAGFIELD
SCURRENT
MAGFIELD
BUS CUTWITH
MAGNETIC
SEFIELD AT
RESET
IQL
IQH
SENSOR 01
相關PDF資料 |
PDF描述 |
|---|---|
| A3059 | HALL-EFFECT GEAR-TOOTH SENSORS -ACCOUPLED |
| A3064L | HALL-EFFECT GEAR-TOOTH SENSORS -ACCOUPLED |
| A3425L | HALL-EFFECT GEAR-TOOTH SENSORS -ACCOUPLED |
| A3064 | HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
| A3064LKA | HALL-EFFECT GEAR-TOOTH SENSOR -AC COUPLED |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A305402 | 功能描述:柵欄接線端子 A305402-NL RoHS:否 制造商:TE Connectivity / AMP 產品:Barrier Terminal Blocks 系列: 類型:Dual Barrier, Flat Block without Mounting Ears 節距:9.53 mm 位置/觸點數量:2 線規量程:22-12 電流額定值:20 A 電壓額定值:300 V 安裝風格:Through Hole 安裝角:Vertical 端接類型:Screw 觸點電鍍:Tin |
| A30540200 | 功能描述:柵欄接線端子 SHIP SCREWS BULK RoHS:否 制造商:TE Connectivity / AMP 產品:Barrier Terminal Blocks 系列: 類型:Dual Barrier, Flat Block without Mounting Ears 節距:9.53 mm 位置/觸點數量:2 線規量程:22-12 電流額定值:20 A 電壓額定值:300 V 安裝風格:Through Hole 安裝角:Vertical 端接類型:Screw 觸點電鍍:Tin |
| A30540203 | 功能描述:柵欄接線端子 MAGNUM A3000 SERIES RoHS:否 制造商:TE Connectivity / AMP 產品:Barrier Terminal Blocks 系列: 類型:Dual Barrier, Flat Block without Mounting Ears 節距:9.53 mm 位置/觸點數量:2 線規量程:22-12 電流額定值:20 A 電壓額定值:300 V 安裝風格:Through Hole 安裝角:Vertical 端接類型:Screw 觸點電鍍:Tin |
| A305402RC | 制造商:Magnum / Cooper 功能描述:Conn Barrier Strip 2 POS 11.1mm Solder ST Thru-Hole 30A |
| A30540300 | 功能描述:柵欄接線端子 CONN TRM BLK SCRW RoHS:否 制造商:TE Connectivity / AMP 產品:Barrier Terminal Blocks 系列: 類型:Dual Barrier, Flat Block without Mounting Ears 節距:9.53 mm 位置/觸點數量:2 線規量程:22-12 電流額定值:20 A 電壓額定值:300 V 安裝風格:Through Hole 安裝角:Vertical 端接類型:Screw 觸點電鍍:Tin |
發布緊急采購，3分鐘左右您將得到回復。