- 您現在的位置：買賣IC網 > PDF目錄375103 > A1642LKTN-I2-T (Allegro MicroSystems, Inc.) Two-Wire True Zero-Speed Miniature Differential Peak-Detecting Sensor with Continuous Calibration PDF資料下載
參數資料
| 型號： | A1642LKTN-I2-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Two-Wire True Zero-Speed Miniature Differential Peak-Detecting Sensor with Continuous Calibration |
| 中文描述： | 雙線真零高速微型差分峰值檢測與連續校準傳感器 |
| 文件頁數： | 11/13頁 |
| 文件大?。?/td> | 336K |
| 代理商： | A1642LKTN-I2-T |
11
A1642LK-DS
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Two-Wire True Zero-Speed Miniature Differential Peak-Detecting Sensor with Continuous Calibration
A1642LK
SENSOR OPERATION
Each operating mode is described in detail below.
Power-On
When power (V
CC
> V
CC(Min)
) is applied to the device, a short
period of time is required to power the various portions of the
IC. During this period, the A1642 powers-on in the high current
state, I
CC(High)
. After power-on, there are conditions that could
induce a change in the output state. Such an event could be
caused by thermal transients, but would require a static applied
magnetic
fi
eld, proper signal polarity, and particular direction
and magnitude of internal signal drift.
Initial Offset Adjust
The sensor initially cancels the effects of chip, magnet, and
installation offsets. Once offsets have been cancelled, the digital
tracking DAC is ready to track the signal and provide output
switching. The period of time required for both Power-On and
Initial Offset Adjust is de
fi
ned as the Power-On Time.
Calibration Mode
The calibration mode allows the sensor to automatically select
the proper signal gain and continue to adjust for offsets. The
AGC is active, and selects the optimal signal gain based on the
amplitude of the V
PROC
signal. Following each adjustment to
the AGC DAC, the Offset DAC is also adjusted to ensure the
internal analog signal is properly centered.
During this mode, the tracking DAC is active and output switch-
ing occurs, but the duty cycle is not guaranteed to be within
speci
fi
cation.
Running Mode
After the Initial Calibration period, C
I
, establishes a signal gain,
the device moves to Running mode. During Running mode, the
sensor tracks the input signal and gives an output edge for every
peak of the signal. AOA remains active to compensate for any
offset drift over time.
The A1642 incorporates a novel algorithm for adjusting the
signal gain during Running mode. This algorithm is designed
to optimize the V
PROC
signal amplitude in instances where the
magnetic signal “seen” during the calibration period is not repre-
sentative of the amplitude of the magnetic signal for the installed
sensor air gap (see
fi
gure 9).
Sensor Electrical
Output, I
OUT
Internal Differential
Signal, V
PROC
B
RP
B
OP
B
OP
B
RP
1
2
3
4
5
Figure 9: Operation of Running Mode Gain Adjust.
Position 1. The device is initially powered-on. Self-calibration occurs.
Position 2. Small amplitude oscillation of the target sends an erroneously small differential signal to the sensor. The ampli-
tude of V
PROC
is greater than the switching hysteresis (B
OP
and B
RP
), and the device output switches.
Position 3. The calibration period completes on the third rising output edge, and the device enters Running mode.
Position 4. True target rotation occurs and the correct magnetic signal is generated for the installation air gap. The estab-
lished signal gain is too large for the target’s rotational magnetic signal at the given air gap.
Position 5. Running Mode Calibration corrects the signal gain to an optimal level for the installation air gap.
相關PDF資料 |
PDF描述 |
|---|---|
| A1776 | Single-Channel, 3 V Front-End Processor for General Purpose Applications Including Speech and Telephony; Package: EVALUATION BOARDS; No of Pins: -; Temperature Range: TBD |
| A19-1 | 10 TO 1000 MHz CASCADABLE AMPLIFIER |
| A2004 | High Voltage High Current Darlington Arrays |
| A2023 | High Voltage High Current Darlington Arrays |
| A2024 | High Voltage High Current Darlington Arrays |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A16435-0009 | 功能描述:重負荷電源連接器 A16 DINW/ 35MMPINCON 35MMPINCON RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| A16435-0019 | 功能描述:重負荷電源連接器 A16 DINW/ 35MMPINCON 35MMPINCON RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| A16435-1009 | 功能描述:重負荷電源連接器 A16 DINW/ 35MMPINCON 35MMPINCON RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| A16435-1019 | 功能描述:重負荷電源連接器 A16 DINW/ 35MMPINCON 35MMPINCON RoHS:否 制造商:Hirose Connector 系列:PS2 產品類型:Connectors 位置/觸點數量: 端接類型:Crimp 觸點材料: 觸點電鍍:Gold 電壓額定值: 電流額定值:300 A 附件類型: |
| A16439-000 | 制造商:TE Connectivity 功能描述:CONN MOD JACK 8P8C |
發布緊急采購，3分鐘左右您將得到回復。