- 您現在的位置：買賣IC網 > PDF目錄375102 > A1382EUA-T (Allegro MicroSystems, Inc.) Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package PDF資料下載
參數資料
| 型號： | A1382EUA-T |
| 廠商： | Allegro MicroSystems, Inc. |
| 英文描述： | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| 中文描述： | 可編程線性霍爾與模擬輸出的微型超薄表面貼裝封裝效應傳感器 |
| 文件頁數： | 12/18頁 |
| 文件大?。?/td> | 415K |
| 代理商： | A1382EUA-T |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁
Programmable Linear Hall Effect Sensors with Analog Output
Available in a Miniature Thin Profile Surface Mount Package
A1381, A1382,
A1383, and A1384
12
Allegro MicroSystems, Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
www.allegromicro.com
Figure 1. Parameter selection pulse train. This shows the sequence for
selecting the register corresponding to key 1, indicated by a single V
PM
pulse.
Parameter Selection
Each programmable parameter can be accessed through a specific
register. To select a register, a sequence of voltage pulses con-
sisting of a V
PH
pulse, a series of V
PM
pulses, and a V
PH
pulse
(with no V
CC
supply interruptions) must be applied serially to
the VOUT pin. The number of V
PM
pulses is called the
key
, and
uniquely identifies each register. The pulse train used for selec-
tion of the first register, key 1, is shown in figure 1.
The A138x has three registers that select among the five pro-
grammable parameters:
Register 1:
Quiescent voltage output, V
OUT(Q)
Register 2:
Sensitivity, Sens
Register 3:
Sensitivity temperature coefficient, TC
Sens
Polarity, POL
Overall device locking, LOCK
Bit Field Addressing
After a programmable parameter has been selected, a V
PH
pulse
transitions the programming logic into the bit field address-
ing state. Applying a series of V
PM
pulses to the VOUT pin of
the device, as shown in figure 2, increments the bit field of the
selected parameter.
When addressing the bit field, the number of V
PM
pulses is rep-
resented by a decimal number called a
. Addressing activates
the corresponding fuse locations in the given bit field by incre-
menting the binary value of an internal DAC. The value of the bit
field (and code) increments by one with the falling edge of each
V
PM
pulse, up to the maximum possible code (see the Program-
ming Logic table). As the value of the bit field code increases, the
value of the programmable parameter changes.
Measurements can be taken after each pulse to determine if the
desired result for the programmable parameter has been reached.
Cycling the supply voltage resets all the locations in the bit field
that have unblown fuses to their initial states.
Fuse Blowing
After the required code is found for a given parameter, its value
can be set permanently by blowing individual fuses in the appro-
priate register bit field. Blowing is accomplished by applying
a V
PH
pulse, called a
blow pulse
, of sufficient duration at the
V
P(HIGH)
level to permanently set an addressed bit by blowing a
fuse internal to the device. Due to power requirements, the fuse
for each bit in the bit field must be blown individually. To accom-
plish this, the code representing the desired parameter value must
be translated to a binary number. For example, as shown
V+
0
V
P(HIGH)
V
P(MID)
V
P(LOW)
C
C
C
n
C
n
V+
0
t
LOW
t
ACTIVE
V
P(HIGH)
V
P(MID)
V
P(LOW)
Figure 2. Bit field addressing pulse train. Addressing the bit field by
incrementing the code causes the programmable parameter value to
change. The number of bits available for a given programming code,
n
,
varies among parameters; for example, the bit field for V
OUT(Q)
has 6 bits
available, which allows 63 separate codes to be used.
Programming Procedures
相關PDF資料 |
PDF描述 |
|---|---|
| A1382EUATI-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1382LLHLT-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1382LUA-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1382LUATI-T | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1383 | Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| A1382EUATI-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
| A1382LLHLT-T | 功能描述:IC SENSOR HALL EFFECT SOT23-W RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:A138x 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1382LLHLX-T | 制造商:ALLEGRO MICROSYSTEMS, LLC 功能描述:IC HALL EFFECT SENSOR SOT-23W |
| A1382LUA-T | 功能描述:IC SENSOR HALL EFFECT PREC 3-SIP RoHS:是 類別:傳感器，轉換器 >> 磁性 - 霍爾效應，數字式開關，線性，羅盤 (IC) 系列:A138x 標準包裝:1 系列:- 傳感范圍:20mT ~ 80mT 類型:旋轉 電源電壓:4.5 V ~ 5.5 V 電流 - 電源:15mA 電流 - 輸出（最大）:- 輸出類型:數字式，PWM，8.5 位串行 特點:可編程 工作溫度:-40°C ~ 150°C 封裝/外殼:20-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:20-SSOP 包裝:Digi-Reel® 其它名稱:AS5132-HSST-500DKR |
| A1382LUATI-T | 制造商:ALLEGRO 制造商全稱:Allegro MicroSystems 功能描述:Programmable Linear Hall Effect Sensors with Analog Output Available in a Miniature Thin Profile Surface Mount Package |
發布緊急采購，3分鐘左右您將得到回復。