3M Static Dissipative Rigid Worksurface 8300 Series Installatio" />
鍙冩暩(sh霉)璩囨枡
鍨嬭櫉锛� 8353
寤犲晢锛� 3M
鏂囦欢闋佹暩(sh霉)锛� 10/16闋�
鏂囦欢澶�?銆�?/td> 0K
鎻忚堪锛� WORKSURFACE RIGID ESD DISSP BGE
妯欐簴鍖呰锛� 1
绯诲垪锛� 8300
澧婂瓙椤炲瀷锛� 妗屽瓙锛屽伐浣滆嚭
褰㈢媭锛� 鐭╁舰
闀峰害锛� 4'锛�1.22m锛�
瀵細 2'锛�0.61m锛�
鍘氬害锛� 0.13"锛�3.30mm锛�
椤忚壊锛� 娣鸿
鏉愯唱(zh矛)锛� Laminate
鐗归粸锛� 鑰楁暎
鍖呮嫭锛� 鎺ュ湴杌熺窔锛屾帴鍦板崱鎵�
鍏跺畠鍚嶇ū锛� 05400718622
83533M
98079815886
3
78-8136-3801-8
3M Static Dissipative Rigid Worksurface 8300 Series
Installation Instructions
1.0
Industry definitions
A.
Backer: a phenolic sheet placed on the opposite (back) side of the substrate to which the laminate is
adhered. The backer is used to offset stresses on the substrate caused by the laminate. It also acts as a
moisture barrier (See Section 10.0).
B.
No drip edge: a raised rim on a counter/benchtop/work surface to prevent runoff.
C.
Glue line: the adhesive layer used to adhere laminate to the surface of a substrate.
D.
Jroller 3 inch: a handheld roller used to apply even pressure when bonding laminate to a surface. A
pressure of 50 pounds per lineal inch is recommended for most contact adhesives.
E.
NEMA: National Electrical Manufacturers鈥� Association
F.
NEMA LD 32000: HighPressure Decorative Laminate
NEMA LD 32000 Annex A: Performance, Applications, Fabrication, & Installation of HighPressure
Decorative Laminate
G.
Off Fall: excess laminate due to dimensional inconsistencies or irregularities in the substrate to which
the laminate is applied.
H.
Postforming: bending laminate sheet over or around the edge profile of a counter; this requires special
procedures (See Section 8.0)
I.
Tempilaq/Templistik: colored marking chalk or wax that is heatsensitive, i.e., changes color or melts
when a certain temperature is reached; used to indicate that the surface of a laminate has reached the
proper temperature for thermoforming (325掳F). (See Section 8.0)
J.
Waterfall edge: a 90掳 postformed edge on a counter.
2.0
3M Static Dissipative Rigid Worksurface 8300 Series Specifications
A.
Resistance values: Resistance measurements are used to establish the chargedraining capability of the
static dissipative rigid worksurface. The ESD Association evaluates two resistance values in classifying
dissipative laminate and other static control surfacing materials. The tests are as follows:
1) Surface to Ground point resistance Use a 3M Test Kit 701 for static control surfaces. Test the
resistance between the top surface of the table top and the ground point per ESD Association
Standard 4.1 [tested at 72掳F (22掳C), 50% RH]. The values should be between 1 x 106 1 x 109 ohms
(l 1,000 Megohms).
2) Point to Point resistance Use a 3M Test Kit 701 for static control surfaces. Test the resistance
between two points on the top surface of the table top per ESD Association Standard 4.1 [Tested at
72掳F (22掳C), 50% RH]. Typical value is 6 x 107 ohms (60 Megohms).
AdditionalTest:
Ground Point to Ground Point resistance 鈥� Perform this test when the worksurface ground connection
is to be electrically monitored. Equipment such as the 3M Workstation Monitor 724 continuously
monitors the ground connection through the interior conductive layer of the laminate. Use a 3M Test
Kit 701 for static control surfaces to pretest and ensure that the grounding hardware is making sufficient
contact to the conductive layer. Connect one of the test leads to each of the two ground hardware items
installed on the tabletop. Set the test selector switch to the 10V position. Push the test button and the
reading should be less than 1 x 106 ohms (1 Megohm).
B.
Thickness: 0.040 in. nominal
C.
Density: 1.45 grams/cc
鐩搁棞(gu膩n)PDF璩囨枡
PDF鎻忚堪
431110-26-0 TERM BARRIER 26CIRC 1 ROW .4375
431103-26-0 TERM BARRIER 26CIRC 1 ROW .4375
431102-26-0 TERM BARRIER 26CIRC 1 ROW .4375
431015-26-0 TERM BARRIER 26CIRC 1 ROW .4375
431010-26-0 TERM BARRIER 26CIRC 1 ROW .4375
鐩搁棞(gu膩n)浠g悊鍟�/鎶€琛�(sh霉)鍙冩暩(sh霉)
鍙冩暩(sh霉)鎻忚堪
83530 鍒堕€犲晢:Brady Corporation 鍔熻兘鎻忚堪:
83-530-5 鍒堕€犲晢:Eaton Corporation 鍔熻兘鎻忚堪:3 CIRCUIT SWITCH UNIT ASSEMBLY
83530-500 鍒堕€犲晢:ABB Control 鍔熻兘鎻忚堪:Welcome Door Entry Sealing Strip
8-353081-2 鍒堕€犲晢:TE Connectivity / AMP 鍔熻兘鎻忚堪:10.16mm 3 IX Right Angle Solder 630VAC Gold Over Nickel
8-353082-2 鍔熻兘鎻忚堪:闆绘簮鍒版澘 DYNAMIC D5200S V-HDR ASY 3P RoHS:鍚� 鍒堕€犲晢:TE Connectivity / AMP 绯诲垪:5787444 鐢�(ch菐n)鍝侀鍨�:Connectors 瑙搁粸椤炲瀷: 闆诲椤嶅畾鍊�:50 V 闆绘祦椤嶅畾鍊�: 绡€(ji茅)璺�: 浣嶇疆/瑙搁粸鏁�(sh霉)閲�:5 瀹夎棰�(f膿ng)鏍�:Through Hole 绔帴椤炲瀷: 瑙搁粸闆婚崓:Tin