DESCO WEST: 3651 WALNUT AVE., CHINO, CA 91710 WEB SITE: www.desco.com
PHONE (909) 627-8178 FAX (909) 627-7449
DESCO EAST: 90 HUDSON RD, CANTON, MA 02021-1407
PHONE (781) 821-8370 FAX (781) 575-0172
DATE:
2/06
2006 DESCO INDUSTRIES INC.
Employee Owned
MATERIAL STATFREE S
DRAWING PM-71
STATFREE S FLOOR MAT, VINYL, HOMOGENEOUS, ANTIFATIGUE, .375" (9.5mm)
Description:
Statfree S material is specifically
designed to reduce fatigue in areas
where standing is required for long
periods of time. This floor mat
combines ESD protection and
durability. The heavy embossed
texture provides slip and soil
resistance. Statfree S meets the
requirements of DOD-HDBK-263,
DOD-STD-2000, ESD-S7.1 and EN
100 015 Issue 1.
Light Grey, Brown
Electrical Properties:
Property
Test Method
Value
RTG Resistance:
ESD S7.1
10E9 - 10E10 Ohms
RTT Resistance:
ESD S7.1
10E9 - 10E10 Ohms
Electrical Properties obtained by testing to industrial standards by an
independent testing laboratory @ 100 Volts and 50% relative humidity
unless otherwise specified. Complete text of the test report is available
upon request.
Specifications:
Construction:
Foamed Homogeneous Vinyl
electrical properties consistent
throughout. Designed specifically to
reduce fatigue as a standing surface.
Thickness:
0.375 inches (9.5mm)
Texture:*
Non-directional, heavy embossed, soil and
abrasion resistant
Color:*
Light grey, brown
Weight:
0.65 lbs/ft2 (0.317g/cm2)
Hardness:
ASTM-D-2240-75 65 Shore “00”
Wear Resistance: Negligible-Tabor Abrader, 500 Cycles CS-17
wheels, 10,000 grams load
Heat Resistance:
-20°F to 140°F continuous
*Color and texture may vary between lots and mills
Grounding: This material must be properly grounded for optimum
electrical performance. Ask for Technical Bulleltin TB-2000 for mat
grounding instructions.
Cleaning: For optimum electrical performance, surface must be
cleaned regularly using an ESD mat cleaner. We suggest using our
Reztore Surface & Mat Cleaner Item #10435 or Static-Wipes
Item #10600. Do not use cleaners with silicone. Silicone buildup
will create an insulative film on the surface.
Disclaimer:
All statements, technical data, and recommendations contained herein are based
upon tests we believe to be reliable. However, the accuracy or completeness
thereof is not guaranteed. The proper and correct applications of products and
data is the responsibility of the user. Statements or recommendations not
contained herein shall have no force or effect unless embodied in a written
agreement signed by authorized offers of Desco Industries, Inc.
Matting materials have a tendency to shrink slightly when first unrolled. In
applications where length is critical, allow the material to relax for at least 4 hours
before cutting to size. Always trim with a sharp knife or razor blade.
Made in America
Hardware is not included with rolls.
Grounding Intervals for ESD Mats
Sufficient ground cords should be used to reliably meet
ANSI/ESD S20.20 Table 1 less than 1 x 10E9 ohms for
worksurfaces. An industry recommendation has been that
continuous runs of ESD matting should be grounded at ten-
foot intervals to allow proper charge decay rates with each
individual ESD mat should be grounded with ground snap
located no further than five feet from either end.
.375" (9.5mm)
THICK ROLLS
COLOR
ITEM NO.
APPROX. WT.
BROWN
82063
130 lb.
STIPPLE
LIGHT GREY
82064
130 lb.
STIPPLE
Roll Stock Size 3' x 60'
(Roll Stock beveled on sides only)
Roll Stock Item Numbers
Limited Lifetime Warranty
Desco warrants for one year that Statfree matting products
will be free of defects in materials and workmanship and will
guarantee dissipative/ conductive mat properties for the life
of the mat. Damage to matting caused by misuse of any
kind, including using inappropriate cleaners is not covered by
Desco Limited Warranty.
Tolerances:
Width ± .250"
Length ± .250" every 1 linear foot
of running material.
RoHS Compliance Statement
None of the following materials are
intentionally added in manufacturing this
product: lead, mercury, cadmium,
hexavalent chromium, polybrominated
biphenyls (PBB) or polybrominated
diphenyl ethers (PBDE) as outlined in
the Directive 2002/95/EC Article 4.1.
See Desco Industries Inc. letter on-line
at Desco.com.