- 您現在的位置：買賣IC網 > PDF目錄370133 > 74VHC4066 (ON SEMICONDUCTOR) Dual 2-Line To 4-Line Decoders/Demultiplexers 16-SOIC -40 to 85 PDF資料下載
參數資料
| 型號： | 74VHC4066 |
| 廠商： | ON SEMICONDUCTOR |
| 英文描述： | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-SOIC -40 to 85 |
| 中文描述： | 四模擬開關/復用器/解復用器 |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 215K |
| 代理商： | 74VHC4066 |
MC74VHC4066
MOTOROLA
VHC Data – Advanced CMOS Logic
DL203 — Rev 2
8
0
–10
–20
–30
–40
–50
1.0
2.0
FREQUENCY (kHz)
d
–60
–70
–80
–90
FUNDAMENTAL FREQUENCY
DEVICE
SOURCE
Figure 15. Plot, Harmonic Distortion
3.0
APPLICATION INFORMATION
The ON/OFF Control pins should be at VCC or GND logic
levels, VCC being recognized as logic high and GND being
recognized as a logic low. Unused analog inputs/outputs
may be left floating (not connected). However, it is advisable
to tie unused analog inputs and outputs to VCC or GND
through a low value resistor. This minimizes crosstalk and
feedthrough noise that may be picked–up by the unused I/O
pins.
The maximum analog voltage swings are determined by
the supply voltages VCC and GND. The positive peak analog
voltage should not exceed VCC. Similarly, the negative peak
analog voltage should not go below GND. In the example
below, the difference between VCC and GND is twelve volts.
Therefore, using the configuration in Figure 16, a maximum
analog signal of twelve volts peak–to–peak can be con-
trolled.
When voltage transients above VCC and/or below GND
are anticipated on the analog channels, external diodes (Dx)
are recommended as shown in Figure 17. These diodes
should be small signal, fast turn–on types able to absorb the
maximum anticipated current surges during clipping. An
alternate method would be to replace the Dx diodes with
MO sorbs (Motorola high current surge protectors).
MO sorbs are fast turn–on devices ideally suited for precise
DC protection with no inherent wear out mechanism.
ANALOG O/I
ON
14
VCC = 12 V
ANALOG I/O
+ 12 V
0 V
+ 12 V
0 V
OTHER CONTROL
INPUTS
(VCC OR GND)
ON
16
VCC
Dx
Dx
VCC
Dx
Figure 16. 12 V Application
Figure 17. Transient Suppressor Application
7
SELECTED
CONTROL
INPUT
Dx
OTHER CONTROL
INPUTS
(VCC OR GND)
7
SELECTED
CONTROL
INPUT
VCC
相關PDF資料 |
PDF描述 |
|---|---|
| 74VHC4066MTC | Quad Analog Switch |
| 74VHC4066 | Quad Analog Switch |
| 74VHC4066M | Dual 2-Line To 4-Line Decoders/Demultiplexers 16-SOIC -40 to 85 |
| 74VHC4066N | Quad Analog Switch |
| 74VHC4066MTCX | SPST Analog Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 74VHC4066_05 | 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:Quad Analog Switch |
| 74VHC4066M | 功能描述:模擬開關 IC Quad Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| 74VHC4066M | 制造商:Fairchild Semiconductor Corporation 功能描述:IC 74VHC CMOS SMD 74VHC4066 |
| 74VHC4066M_Q | 功能描述:模擬開關 IC Quad Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
| 74VHC4066MTC | 功能描述:模擬開關 IC Quad Analog Switch RoHS:否 制造商:Texas Instruments 開關數量:2 開關配置:SPDT 開啟電阻（最大值）:0.1 Ohms 切換電壓（最大）: 開啟時間（最大值）: 關閉時間（最大值）: 工作電源電壓:2.7 V to 4.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-16 |
發布緊急采購，3分鐘左右您將得到回復。