參數資料
型號: 74F160A
廠商: Fairchild Semiconductor Corporation
元件分類: 通用總線功能
英文描述: Synchronous Presettable BCD Decade Counter
中文描述: 同步可預置BCD碼十年計數器
文件頁數: 3/7頁
文件大?。?/td> 72K
代理商: 74F160A
3
www.fairchildsemi.com
7
Functional Description
The 74F160A and 74F162A count modulo-10 in the BCD
(8421) sequence. From state 9 (HLLH) they increment to
state 0 (LLLL). The clock inputs of all flip-flops are driven in
parallel through a clock buffer. Thus all changes of the Q
outputs (except due to Master Reset of the (F160A) occur
as a result of, and synchronous with, the LOW-to-HIGH
transition of the CP input signal. The circuits have four fun-
damental modes of operation, in order of precedence:
asynchronous reset (F160A), synchronous reset (F162A),
parallel load, count-up and hold. Five control inputs—Mas-
ter Reset (MR, F160A), Synchronous Reset (SR, F162A),
Parallel Enable (PE), Count Enable Parallel (CEP) and
Count Enable Trickle (CET)—determine the mode of oper-
ation, as shown in the Mode Select Table. A LOW signal on
MR overrides all other inputs and asynchronously forces all
outputs LOW. A LOW signal on SR overrides counting and
parallel loading and allows all outputs to go LOW on the
next rising edge of CP. A LOW signal on PE overrides
counting and allows information on the Parallel Data (P
n
)
inputs to be loaded into the flip-flops on the next rising
edge of CP. With PE and MR (F160A) or SR (F162A)
HIGH, CEP and CET permit counting when both are HIGH.
Conversely, a LOW signal on either CEP or CET inhibits
counting.
The F160A and F162A use D-type edge-triggered flip-flops
and changing the SR, PE, CEP and CET inputs when the
CP is in either state does not cause errors, provided that
the recommended setup and hold times, with respect to the
rising edge of CP, are observed.
The Terminal Count (TC) output is HIGH when CET is
HIGH and counter is in state 9. To implement synchronous
multistage counters, the TC outputs can be used with the
CEP and CET inputs in two different ways. Please refer to
the F568 data sheet. The TC output is subject to decoding
spikes due to internal race conditions and is therefore not
recommended for use as a clock or asynchronous reset for
flip-flops, counters or registers. In the F160A and F162A
decade counters, the TC output is fully decoded and can
only be HIGH in state 9. If a decade counter is preset to an
illegal state, or assumes an illegal state when power is
applied, it will return to the normal sequence within two
counts, as shown in the State Diagram.
Logic Equations:
Count Enable
=
CEP
×
CET
×
PE
TC
=
Q
0
×
Q
1
×
Q
2
×
Q
3
×
CET
Mode Select Table
*For 74’F162A only
H
=
HIGH Voltage Level
L
=
LOW Voltage Level
X
=
Immaterial
State Diagram
Logic Diagram
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
*SR
PE
CET CEP
Action on the Rising
Clock Edge (
Reset (Clear)
Load (P
n
Q
n
)
Count (Increment)
No Change (Hold)
No Change (Hold)
)
L
H
H
H
H
X
L
H
H
H
X
X
H
L
X
X
X
H
X
L
相關PDF資料
PDF描述
74F162A Synchronous Presettable BCD Decade Counter
74F160APC Synchronous Presettable BCD Decade Counter
74F160ASC Synchronous Presettable BCD Decade Counter
74F160ASJ Synchronous Presettable BCD Decade Counter
74F162APC Synchronous Presettable BCD Decade Counter
相關代理商/技術參數
參數描述
74F160A WAF 制造商:Fairchild Semiconductor Corporation 功能描述:
74F160AD 制造商:n/a 功能描述:74F160 MOT/SIG S1I2A
74F160ADC 制造商:Rochester Electronics LLC 功能描述:- Bulk
74F160APC 功能描述:計數器 IC Syn BCD Decade Ctr RoHS:否 制造商:NXP Semiconductors 計數器類型:Binary Counters 邏輯系列:74LV 位數:10 計數法: 計數順序: 工作電源電壓:1 V to 5.5 V 工作溫度范圍:- 40 C to + 125 C 封裝 / 箱體:SOT-109 封裝:Reel
74F160AS 制造商:Texas Instruments 功能描述: