- 您現在的位置：買賣IC網 > PDF目錄16281 > 73S8024RN-DB (Maxim Integrated Products)BOARD DEMO 73S8024RN 28-SOIC PDF資料下載
參數資料
| 型號： | 73S8024RN-DB |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 2/27頁 |
| 文件大小： | 0K |
| 描述： | BOARD DEMO 73S8024RN 28-SOIC |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 1 |
| 系列： | * |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
73S8024RN Data Sheet
DS_8024RN_020
10
Rev. 2
7 Activation Sequence
The 73S8024RN smart card interface IC has an internal 10ms delay at power on reset or on the
application of VDD > VDDF. No activation is allowed at this time. The CMDVCC (edge triggered) must then
be set low to activate the card. In order to initiate activation, the card must be present; there can be no
over-temperature fault or no VDD fault.
The following steps show the activation sequence and the timing of the card control signals when the
system controller sets CMDVCC low while the RSTIN is low:
CMDVCC
is set low.
Next, the internal VCC control circuit checks the presence of VCC at the end of t1. In normal operation,
the voltage VCC to the card becomes valid during t1. If VCC does not become valid, the OFF goes low
to report a fault to the system controller, and the power VCC to the card is shut off.
Turn I/O (AUX1, AUX2) to reception mode at the end of (t2).
CLK is applied to the card at the end of (t3).
RST is a copy of RSTIN after (t4). RSTIN may be set high before t4, however the sequencer will not
set RST high until 42000 clock cycles after the start of CLK.
CMDVCC
VCC
I/O
CLK
RSTIN
t1
t2
t3
t4
RST
t1 = 0.510 ms (timing by 1.5MHz internal Oscillator)
t2 = 1.5s, I/O goes to reception state
t3 = >0.5s, CLK starts
t4 ≥ 42000 card clock cycles. Time for RST to become the copy of RSTIN
Figure 2: Activation Sequence – RSTIN Low When CMDVCC Goes Low
相關PDF資料 |
PDF描述 |
|---|---|
| M3CKK-2018R | IDC CABLE - MKC20K/MC20M/MPK20K |
| M3AKK-2018R | IDC CABLE - MSC20K/MC20M/MPK20K |
| M3TTK-2618R | IDC CABLE - MSD26K/MC26M/MSD26K |
| A3DDB-4018M | IDC CABLE- AKR40B/AE40M/AKR40B |
| UBC1V471MNS1MS | CAP ALUM 470UF 35V 20% SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 73S8024RN-IL | 制造商:TERIDIAN 功能描述: 制造商:TDK 功能描述:SPECIALTY ANALOG CIRCUIT, 28 Pin Plastic SMT |
| 73S8024RN-IL/F | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-IL/F1 | 功能描述:輸入/輸出控制器接口集成電路 Smart Card Interface ISO7816-3 & EVM4.0 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-IL/F2 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
| 73S8024RN-IL/F3 | 功能描述:輸入/輸出控制器接口集成電路 RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。