參數資料
型號: 6N140A/883B#600
元件分類: 光電耦合器
英文描述: 4 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 0.1 Mbps
封裝: HERMETIC SEALED, DIP-16
文件頁數: 12/12頁
文件大?。?/td> 1110K
代理商: 6N140A/883B#600
9
Notes:
1. GND Pin should be the most negative voltage at the detector side.
Keeping VCC as low as possible, but greater than 2.0 V, will provide
lowest total IOH over temperature.
2. Output power is collector output power plus total supply power for
the single channel device. For the dual channel device, output power
is collector output power plus one half the total supply power. For
the quad channel device, output power is collector output power
plus one fourth of total supply power. Derate at 1.66 mW/°C above
110°C.
3. Derate IF at 0.33 mA/°C above 110°C.
4. Each channel.
5. CURRENT TRANSFER RATIO is defined as the ratio of output collector
current, IO, to the forward LED input current, IF, times 100%.
6. IOHX is the leakage current resulting from channel to channel optical
crosstalk. IF = 2 A for channel under test. For all other channels,
IF = 10 mA.
7. All devices are considered two-terminal devices; measured between
all input leads or terminals shorted together and all output leads or
terminals shorted together.
8. Measured between each input pair shorted together and all output
connections for that channel shorted together.
9. Measured between adjacent input pairs shorted together for each
multi-channel device.
10. CML is the maximum rate of rise of the common mode voltage that
can be sustained with the output voltage in the logic low state
(VO < 0.8 V). CMH is the maximum rate of fall of the common mode
voltage that can be sustained with the output voltage in the logic
high state (VO > 2.0 V).
11. In applications where dV/dt may exceed 50,000 V/
s (such as
a static discharge) a series resistor, RCC, should be included to
protect the detector ICs from destructively high surge currents. The
recommended value is:
1 (V)
RCC = ————— kΩ
0.15 IF (mA)
for single channel;
1 (V)
RCC = ————— kΩ
0.3 IF (mA)
for dual channel;
1 (V)
RCC = ————— kΩ
0.6 IF (mA)
for quad channel.
12. This is a momentary withstand test, not an operating condition.
13. Standard parts receive 100% testing at 25°C (Subgroups 1 and
9). SMD and 883B parts receive 100% testing at 25,125, and -55°C
(Subgroups 1 and 9, 2 and 10, 3 and 11, respectively).
14. Parameters tested as part of device initial characterization and
after design and process changes. Parameters guaranteed to limits
specified for all lots not specifically tested.
15. The HCPL-6730, HCPL-6731, and HCPL-673K dual channel parts
function as two independent single channel units. Use the single
channel parameter limits.
16. Not required for 6N140A, 6N140A/883B, HCPL-177K, HCPL-
6750/51/5K, 8302401, and 5962-9800201 types.
17. Required for 6N140A, 6N140A/883B, HCPL-177K, HCPL-6750/51/5K,
8302401, and 5962-9800201 types.
相關PDF資料
PDF描述
62D03-02-040CH SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER
61A24-090 ROTARY OPTICAL POSITION ENCODER
62S18-N0-190ST SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER
62S11-H9-135SHT SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER
62S11-H0-200SHT SINGLE, 2 CHANNELS, ROTARY OPTICAL POSITION ENCODER
相關代理商/技術參數
參數描述
6N140ATXV 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic
6N140TXV 功能描述:邏輯輸出光電耦合器 4Ch 1500%CTR Hermetically sealed RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
6N140TXVB 功能描述:邏輯輸出光電耦合器 4Ch 1500%CTR Hermetically sealed RoHS:否 制造商:Fairchild Semiconductor 絕緣電壓:4243 Vrms 輸出類型:Push-Pull 最大傳播延遲時間:500 ns 最大正向二極管電壓: 最大反向二極管電壓: 最大正向二極管電流: 最大連續輸出電流:2.5 A 最大功率耗散:100 mW 最大工作溫度:+ 100 C 最小工作溫度:- 40 C 封裝 / 箱體:SO-16 封裝:Tube
6N-20 制造商:Aeroflex / Inmet 功能描述:ATTENUATOR - FIXED COAXIAL
6N20W-03 制造商:Aeroflex / Inmet 功能描述:ATTENUATOR - FIXED COAXIAL