- 您現在的位置：買賣IC網 > PDF目錄371610 > 544MI-01 Clock Divider PDF資料下載
參數資料
| 型號： | 544MI-01 |
| 英文描述： | Clock Divider |
| 中文描述： | 時鐘分頻器 |
| 文件頁數： | 2/7頁 |
| 文件大小： | 107K |
| 代理商： | 544MI-01 |
Clock Divider
MDS 544M-01 A
2
Revision 041505
Integrated Circuit Systems, Inc.
●
525 Race Street, San Jose, CA 95126
●
tel (408) 297-1201
●
www.icst.com
ICS544-01
P R E L I M I N A R Y I N F O R M AT I O N
Pin Assignment
8-pin (150 mil) SOIC
Clock Divider Table
0 = connect directly to ground
1 = connect directly to VDD
Pin Descriptions
External Components
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50
trace (a
commonly used trace impedance), place a 33
resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20
.
On chip capacitors
- Crystal capacitors should be
connected from pins X1 to ground and X2 to ground to
optimize the initial accuracy. The value (in pf) of these
crystal caps equal (C
L
-12)*2 in this equation,
C
L
=crystal load capacitance in pf. For example, for a
crystal with a 16 pF load cap, each external crystal cap
would be 8 pF. [(16-12)x2]=8.
Decoupling Capacitor
As with any high-performance mixed-signal IC, the
ICS544-01 must be isolated from system power supply
noise to perform optimally.
A decoupling capacitor of 0.01μF must be connected
between VDD and the PCB ground plane.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) The 0.01μF decoupling capacitor should be mounted
on the component side of the board as close to the
X1/ICLK
X2
GND
VDD
S0
OE
CLK
S1
1
2
3
4
8
7
6
5
S1
0
0
1
1
S0
0
1
0
1
CLK
Input/32
Input/64
Input/256
Input/512
Pin
Number
1
2
3
Pin
Name
X1/ICLK
X2
GND
Pin
Type
XI
Xo
Power
Pin Description
Crystal or Clock input.
Connect to crystal for crystal input and leave open for clock input.
Connect to ground.
Select 0 for output clock. Connect to GND or VDD, per divider table above.
Internal pull-up resistor.
Clock output per table above.
Output Enable.Tri-states output clock when low. Also shuts down the oscillator
circuit. Internal pull-up resistor. OE=1 normal operation.
Connect to 2.25 V to 3.6 V.
Select 1 for output clock. Connect to GND or VDD, per divider table above.
Internal pull-up resistor.
4
S0
Input
5
CLK
Output
6
OE
Input
7
VDD
Power
8
S1
Input
相關PDF資料 |
PDF描述 |
|---|---|
| 544MI01L | Clock Divider |
| 5451DM | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 5451DMQB | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| 5451FMQB | Dual/Triple Ultra-Low-Voltage SOT23 µP Supervisory Circuits |
| DM5451J | Dual 2/2-input AND-NOR Gate |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 544MI01L | 制造商:ICS 制造商全稱:ICS 功能描述:Clock Divider |
| 544MI-01LF | 制造商:Integrated Device Technology Inc 功能描述:CLOCK DIVIDER 制造商:Integrated Device Technology Inc 功能描述:CLOCK DIVIDER 8SOIC - Rail/Tube |
| 544MI-01LFT | 功能描述:時鐘驅動器及分配 CLOCK DIVIDER RoHS:否 制造商:Micrel 乘法/除法因子:1:4 輸出類型:Differential 最大輸出頻率:4.2 GHz 電源電壓-最大: 電源電壓-最小:5 V 最大工作溫度:+ 85 C 封裝 / 箱體:SOIC-8 封裝:Reel |
| 544P4P144 | 功能描述:電纜組件 MINI-MIZER RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規（AWG）:20, 28 長度:0.305 m 顏色:Black, Red |
| 544P4P36 | 功能描述:電纜組件 MINI-MIZER RoHS:否 制造商:Molex 產品:Power Assemblies 類型:Cable Assembly 連接器端口 A:No Connector 連接器端口 A 管腳計數:4 連接器端口 B:No Connector 連接器端口 B 管腳計數: 型式:Male 線規 - 美國線規（AWG）:20, 28 長度:0.305 m 顏色:Black, Red |
發布緊急采購，3分鐘左右您將得到回復。