- 您現在的位置：買賣IC網 > PDF目錄63161 > 411MLF (INTEGRATED DEVICE TECHNOLOGY INC) 411 SERIES, PLL BASED CLOCK DRIVER, 3 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 PDF資料下載
參數資料
| 型號： | 411MLF |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 411 SERIES, PLL BASED CLOCK DRIVER, 3 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| 封裝： | 0.150 INCH, ROHS COMPLIANT, SOIC-8 |
| 文件頁數： | 3/6頁 |
| 文件大?。?/td> | 154K |
| 代理商： | 411MLF |
ICS411
PC PERIPHERAL CLOCK
CLOCK SYNTHESIZER
IDT / ICS PC PERIPHERAL CLOCK
3
ICS411
REV E 051310
External Components
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50
trace (a
commonly used trace impedance), place a 33
resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20
.
Decoupling Capacitor
As with any high performance mixed-signal IC, the
ICS411 must be isolated from system power supply
noise to perform optimally.
Decoupling capacitors of 0.01F must be connected
between each VDD pin and the PCB ground plane.
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) 0.01F decoupling capacitors should be mounted on
the component side of the board as close to the VDD
pin as possible. No vias should be used between
decoupling capacitor and VDD pin. The PCB trace to
VDD pin should be kept as short as possible, as should
the PCB trace to the ground via.
2) To minimize EMI the 33
series termination resistor,
if needed, should be placed close to the clock output.
3) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers. Other signal traces should be routed away
from the ICS411. This includes signal traces just
underneath the device, or on layers adjacent to the
ground plane layer used by the device.
Absolute Maximum Ratings
Stresses above the ratings listed below can cause permanent damage to the ICS411. These ratings, which
are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the
device at these or any other conditions above those indicated in the operational sections of the
specifications is not implied. Exposure to absolute maximum rating conditions for extended periods can
affect product reliability. Electrical parameters are guaranteed only over the recommended operating
temperature range.
Recommended Operation Conditions
Item
Rating
Supply Voltage, VDD
7 V
All Inputs and Outputs
-0.5 V to VDD+0.5 V
Ambient Operating Temperature
0 to +70
° C
Storage Temperature
-65 to +150
° C
Junction Temperature
125
° C
Soldering Temperature
260
° C
Parameter
Min.
Typ.
Max.
Units
Ambient Operating Temperature
0
–
+70
° C
Power Supply Voltage (measured in respect to GND)
+3.00
+3.60
V
相關PDF資料 |
PDF描述 |
|---|---|
| 411M | 411 SERIES, PLL BASED CLOCK DRIVER, 3 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO8 |
| 41PCS170TO5 | SINGLE COLOR LED ARRAY, ORANGE |
| 41PCT070TG4 | T-3/4 SINGLE COLOR LED ARRAY, GREEN, 1.8 mm |
| 41PCT070TY4 | T-3/4 SINGLE COLOR LED ARRAY, YELLOW, 1.8 mm |
| 41PCT070TWYG4-REV | T-3/4 DUAL COLOR LED ARRAY, YELLOW/HIGH EFFICIENCY GREEN, 1.8 mm |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 411MLFT | 功能描述:時鐘合成器/抖動清除器 PC PERIPHERAL CLOCK RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| 411MS8GE | 制造商:HITTITE 制造商全稱:Hittite Microwave Corporation 功能描述:GaAs MMIC SINGLE-BALANCED MIXER, 10 - 15 GHz |
| 411N1405-7A | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 411N1405-7G | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 411P | 功能描述:SCOTCH OUTDOOR MOUNTING TAPE 411 制造商:3m 系列:* 零件狀態:在售 標準包裝:6 |
發布緊急采購，3分鐘左右您將得到回復。