- 您現在的位置：買賣IC網 > PDF目錄358631 > 3802 (Mitsubishi Electric Corporation) TRANS PREBIASED NPN 200MW SOT-23 PDF資料下載
參數資料
| 型號： | 3802 |
| 廠商： | Mitsubishi Electric Corporation |
| 英文描述： | TRANS PREBIASED NPN 200MW SOT-23 |
| 中文描述： | 單芯片8位CMOS微機 |
| 文件頁數： | 20/51頁 |
| 文件大?。?/td> | 692K |
| 代理商： | 3802 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
MITSUBISHI MICROCOMPUTERS
3802 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
20
Fig. 13 Operation of UART serial I/O function
Serial I/O1 control register (SIO1CON) 001A
16
The serial I/O control register consists of eight control bits for the
serial I/O function.
UART control register (UARTCON) 001B
16
The UART control register consists of four control bits (bits 0 to 3)
which are valid when asynchronous serial I/O is selected and set
the data format of an data transfer. One bit in this register (bit 4) is
always valid and sets the output structure of the P4
5
/T
X
D pin.
Serial I/O1 status register (SIO1STS) 0019
16
The read-only serial I/O1 status register consists of seven flags
(bits 0 to 6) which indicate the operating status of the serial I/O
function and various errors.
Three of the flags (bits 4 to 6) are valid only in UART mode.
The receive buffer full flag (bit 1) is cleared to “0” when the receive
buffer is read.
If there is an error, it is detected at the same time that data is
transferred from the receive shift register to the receive buffer, and
the receive buffer full flag is set. A write to the serial I/O status reg-
ister clears all the error flags OE, PE, FE, and SE (bit 3 to bit 6, re-
spectively). Writing “0” to the serial I/O enable bit SIOE (bit 7 of
the Serial I/O Control Register) also clears all the status flags, in-
cluding the error flags.
All bits of the serial I/O1 status register are initialized to “0” at re-
set, but if the transmit enable bit (bit 4) of the serial I/O control reg-
ister has been set to “1”, the transmit shift completion flag (bit 2)
and the transmit buffer empty flag (bit 0) become “1”.
Transmit buffer/Receive buffer register (TB/
RB) 0018
16
T
he transmit buffer and the receive buffer are located at the same
address. The transmit buffer is write-only and the receive buffer is
read-only. If a character bit length is 7 bits, the MSB of data stored
in the receive buffer is “0”.
Baud rate generator (BRG) 001C
16
The baud rate generator determines the baud rate for serial trans-
fer.
The baud rate generator divides the frequency of the count source
by 1/(n + 1), where n is the value written to the baud rate genera-
tor.
TSC=0
TBE=1
RBF=0
TBE=0
TBE=0
RBF=1
RBF=1
ST
D
0
D
1
SP
D
0
D
1
ST
SP
TBE=1
TSC=1
ST
D
0
D
1
SP
D
0
D
1
ST
SP
Transmit or receive clock
Transmit buffer write
signal
Generated at 2nd bit in 2-stop-bit mode
1 start bit
7 or 8 data bit
1 or 0 parity bit
1 or 2 stop bit (s)
1:
Error flag detection occurs at the same time that the RBF flag becomes "1" (at 1st stop bit, during reception).
2:
The transmit interrupt (TI) can be selected to occur when either the TBE or TSC flag becomes "1", depending on the setting of the transmit interrupt
source selection bit (TIC) of the serial I/O control register.
3:
The receive interrupt (RI) is set when the RBF flag becomes "1".
4:
After data is written to the transmit buffer when TSC=1, 0.5 to 1.5 cycles of the data shift cycle is necessary until changing to TSC=0.
Notes
8
8
Serial output T
X
D
Serial input R
X
D
Receive buffer read
signal
相關PDF資料 |
PDF描述 |
|---|---|
| 3803X | SUPER BRIGHT LED |
| 381LQ123M035A012 | 105 C Compact, High-Ripple Snap-in |
| 381LQ123M035J042 | 105 C Compact, High-Ripple Snap-in |
| 381LQ123M035K022 | 105 C Compact, High-Ripple Snap-in |
| 381LQ123M050A032 | 105 C Compact, High-Ripple Snap-in |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 3802_M | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:8-BIT SINGLE-CHIP MICROCOMPUTER 740 FAMILY / 38000 SERIES |
| 38020 | 功能描述:DIN導軌式接線端子 1poledistiblock,250A IN 1 RoHS:否 制造商:Phoenix Contact 類型:Feed Through Modular Terminal Block 位置/觸點數量:1 線規量程:26-14 電流額定值:5 A, 15 A 電壓額定值:300 V, 600 V 安裝風格: 端接類型:Push-In |
| 38-020 | 功能描述:SET 3/8DR 6PT 20MM 制造商:apex tool group 系列:* 零件狀態:在售 標準包裝:1 |
| 380200 | 制造商:Weidmuller 功能描述:TB14, ENCLOSURE,4GP,ST, ZINC -EA - Bulk |
| 380-200 | 制造商:Circuit Test 功能描述:TEST LEADS - MEDIUM CLIP PKG/10 (2 EACH - 5 C |
發布緊急采購，3分鐘左右您將得到回復。