- 您現在的位置：買賣IC網 > PDF目錄370038 > 29400 (AMIC Technology Corporation) 512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory PDF資料下載
參數資料
| 型號： | 29400 |
| 廠商： | AMIC Technology Corporation |
| 英文描述： | 512K X 8 Bit / 256K X 16 Bit CMOS 5.0 Volt-only, Boot Sector Flash Memory |
| 中文描述： | 為512k × 8位/ 256 × 16位的CMOS 5.0伏只，引導扇區閃存 |
| 文件頁數： | 15/33頁 |
| 文件大?。?/td> | 497K |
| 代理商： | 29400 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁
A29400 Series
PRELIMINARY (February, 2001, Version 0.1)
15
AMIC Technology, Inc.
I/O
5
: Exceeded Timing Limits
I/O
5
indicates whether the program or erase time has
exceeded a specified internal pulse count limit. Under
these conditions I/O
5
produces a "1." This is a failure
condition that indicates the program or erase cycle was
not successfully completed.
The I/O
5
failure condition may appear if the system tries to
program a "1 "to a location that is previously programmed
to "0." Only an erase operation can change a "0" back to a
"1." Under this condition, the device halts the operation,
and when the operation has exceeded the timing limits,
I/O
5
produces a "1."
Under both these conditions, the system must issue the
reset command to return the device to reading array data.
I/O
3
: Sector Erase Timer
After writing a sector erase command sequence, the
system may read I/O
3
to determine whether or not an
erase operation has begun. (The sector erase timer does
not apply to the chip erase command.) If additional
sectors are selected for erasure, the entire time-out also
applies after each additional sector erase command.
When the time-out is complete, I/O
3
switches from "0" to
"1." The system may ignore I/O
3
if the system can
guarantee that the time between additional sector erase
commands will always be less than 50
μ
s. See also the
"Sector Erase Command Sequence" section.
After the sector erase command sequence is written, the
system should read the status on I/O
7
(
Data
Polling) or
I/O
6
(Toggle Bit 1) to ensure the device has accepted the
command sequence, and then read I/O
3
. If I/O
3
is "1", the
internally controlled erase cycle has begun; all further
commands (other than Erase Suspend) are ignored until
the erase operation is complete. If I/O
3
is "0", the device
will accept additional sector erase commands. To ensure
the command has been accepted, the system software
should check the status of I/O
3
prior to and following each
subsequent sector erase command. If I/O
3
is high on the
second status check, the last command might not have
been accepted. Table 6 shows the outputs for I/O
3
.
START
Read I/O
7
-I/O
0
Toggle Bit
= Toggle
Program/Erase
Operation Not
Commplete, Write
Reset Command
Yes
Notes :
1. Read toggle bit twice to determine whether or not it is
toggling. See text.
2. Recheck toggle bit because it may stop toggling as I/O
5
changes to "1". See text.
No
Read I/O
7
- I/O
0
Twice
I/O
5
= 1
Toggle Bit
= Toggle
Yes
Yes
Program/Erase
Operation Complete
No
No
Read I/O
7
-I/O
0
(Notes 1,2)
Figure 5. Toggle Bit Algorithm
(Note 1)
相關PDF資料 |
PDF描述 |
|---|---|
| 298D475X0025P2T | Solid Tantalum Chip Capacitors MICROTAN⑩ Lead Frameless Molded |
| 298D475X06R3M2T | Solid Tantalum Chip Capacitors MICROTAN⑩ Lead Frameless Molded |
| 298D476X0004M2T | Solid Tantalum Chip Capacitors MICROTAN⑩ Lead Frameless Molded |
| 298D476X0010P2T | Solid Tantalum Chip Capacitors MICROTAN⑩ Lead Frameless Molded |
| 298D476X02R5M2T | Solid Tantalum Chip Capacitors MICROTAN⑩ Lead Frameless Molded |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 29-4000 | 制造商:AIM Cambridge Connectivity Solutions 功能描述: |
| 2940001-01 | 制造商:Bel Fuse 功能描述:- Bulk |
| 2940-00-141-9026 | 制造商: 功能描述: 制造商:undefined 功能描述: |
| 2940001929182 | 制造商: 功能描述: 制造商:MASSEY-FERGUSON INC NORTH 功能描述: 制造商:undefined 功能描述: |
| 2940002-01 | 制造商:Stewart Connector 功能描述:ETHERNET CONN KIT W/TOOL 制造商:BEL STEWART CONNECTOR 功能描述:STEWART, INTERNAL PART #: 2940002-01 |
發布緊急采購，3分鐘左右您將得到回復。