- 您現在的位置：買賣IC網 > Datasheet目錄1 > 204-10SYGT/S530-E2 (Everlight Electronics Co Ltd)LED 3MM SUPER YLW-GRN GRN TRANSF Datasheet資料下載
參數資料
| 型號： | 204-10SYGT/S530-E2 |
| 廠商： | Everlight Electronics Co Ltd |
| 文件頁數： | 6/8頁 |
| 文件大小： | 222K |
| 描述： | LED 3MM SUPER YLW-GRN GRN TRANSF |
| 標準包裝： | 1,000 |
| 顏色： | 綠 |
| Millicandela 等級： | 200mcd |
| 正向電壓： | 2V |
| 電流 - 測試： | 20mA |
| 波長 - 主： | 573nm |
| 波長 - 峰值： | 575nm |
| 視角： | 20° |
| 透鏡類型： | 透明，有色 |
| 透鏡樣式/尺寸： | 圓形，帶圓頂，3mm |
| 封裝/外殼： | 徑向 |
| 高度： | 5.20mm |
| 安裝類型： | 通孔 |
| 包裝： | 散裝 |
DATASHEET
LAMP
204-10SYGT/S530-E2
6
Copyright ?2010, Everlight All Rights Reserved. Release Date : Nov.21. 2013. Issue No: DLE-0006325_Rev.4
www.everlight.com
Prehead
laminar wave
Fluxing
1. Lead Forming
During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy bulb.
Lead forming should be done before soldering.
Avoid stressing the LED package during leads forming. The stress to the base may damage the LEDs characteristics or it
may break the LEDs.
Cut the LED lead frames at room temperature. Cutting the lead frames at high temperatures may cause failure of the LEDs.
When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead position of the LED. If the LEDs
are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the LEDs.
2. Storage
The LEDs should be stored at 30?C or less and 70%RH or less after being shipped from Everlight and the storage life limits
are 3 months. If the LEDs are stored for 3 months or more, they can be stored for a year in a sealed container with a
nitrogen atmosphere and moisture absorbent material.
Please avoid rapid transitions in ambient temperature, especially, in high humidity environments where condensation can
occur.
3. Soldering
Careful attention should be paid during soldering. When soldering, leave more then 3mm from solder joint to epoxy bulb,
and soldering beyond the base of the tie bar is recommended.
Recommended soldering conditions:
Hand Soldering
DIP Soldering
Temp. at tip of iron
300
Max. (30W Max.)
Preheat temp.
100
Max. (60 sec Max.)
Soldering time
3 sec Max.
Bath temp. & time
260 Max., 5 sec Max
Distance
3mm Min.(From solder
joint to epoxy bulb)
Distance
3mm Min. (From solder
joint to epoxy bulb)
Recommended soldering profile
Avoiding applying any stress to the lead frame while the LEDs are at high temperature particularly when soldering.
Dip and hand soldering should not be done more than one time
After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or vibration until the LEDs return to
room temperature.
A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.
相關PDF資料 |
PDF描述 |
|---|---|
| 204-10USOC/S400-A9 | LED 3MM SUPER SUNSET ORANGE CLR |
| 204-15/T2C3-4LQA | LED 3MM INGAN WHITE WATER CLEAR |
| 264-10UYD/S530-A3 | LED 3MM ARRAY SUPER YLW YLW DIFF |
| 264-7SDRD/S530-A3 | LED 3MM SUPER DEEP RED RED DIFF |
| 264-7SURC/S400-A8 | LED 3MM ALGAINP HYPER RED CLR |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 204-10SYGT-S530-E2_05 | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:3.0mm Round Type LED Lamps |
| 204-10UBGC/S400-A4 | 功能描述:標準LED-通孔 Bluish Green RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| 204-10UBGC/S400-A5 | 功能描述:標準LED-通孔 Bluish Green RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| 204-10UBGC/S400-A6 | 功能描述:標準LED-通孔 Bluish Green RoHS:否 制造商:Vishay Semiconductors 照明顏色:Red 光強度:0.7 mcd 波長/色溫:615 nm 顯示角:45 deg 透鏡顏色/類型:Clear, Non-Diffused 正向電流:70 mA 正向電壓:1.83 V to 3.03 V LED 大小:2 mm 系列: 封裝:Tube |
| 204-10UBGC-S400-A6 | 制造商:EVERLIGHT 制造商全稱:Everlight Electronics Co., Ltd 功能描述:3.0mm Round Type LED Lamps |
發布緊急采購，3分鐘左右您將得到回復。