The following sample programs can be found in the
參數資料
型號： 20-101-1068
廠商： Rabbit Semiconductor
文件頁數： 79/160頁
文件大?。?/td> 0K
描述： MODULE RABBITCORE RCM3315
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM3315
其它名稱： 316-1114
User’s Manual
19
3.2.1 Use of Serial Flash
3.2.1.1 Onboard Serial Flash
The following sample programs can be found in the SAMPLES\RCM3300\SerialFlash
folder.
SFLASH_INSPECT.c
—This program is a handy utility for inspecting the contents of a
serial flash chip. When the sample program starts running, it attempts to initialize a
serial flash chip on Serial Port B. Once a serial flash chip is found, the user can perform
two different commands to either print out the contents of a specified page or clear (set
to zero) all the bytes in a specified page.
SFLASH_LOG.c
—This program runs a simple Web server and stores a log of hits in
the serial flash. This log can be viewed and cleared from a browser.
3.2.1.2 SF1000 Serial Flash Card
The following sample program can be found in the SAMPLES\RCM3300\SF1000 folder.
SERFLASHTEST.c
—An optional SF1000 Serial Flash card is required to run this dem-
onstration. Install the Serial Flash card into socket J11 on the Prototyping Board. This
sample program demonstrates how to read and write from/to the Serial Flash card.
3.2.2 Serial Communication
The following sample programs can be found in the SAMPLES\RCM3300\SERIAL folder.
FLOWCONTROL.C
—This program demonstrates hardware flow control by configuring
Serial Port F for CTS/RTS with serial data coming from TxE (Serial Port E) at 115,200
bps. One character at a time is received and is displayed in the STDIO window.
To set up the Prototyping Board, you will need to tie
TxE and RxE together on the RS-232 header at J14,
and you will also tie TxF and RxF together as shown in
the diagram.
A repeating triangular pattern should print out in the
STDIO
window. The program will periodically switch flow control on or off to demon-
strate the effect of no flow control.
PARITY.C
—This program demonstrates the use of parity modes by repeatedly sending
byte values 0–127 from Serial Port E to Serial Port F. The program will switch between
generating parity or not on Serial Port E. Serial Port F will always be checking parity,
so parity errors should occur during every other sequence.
To set up the Prototyping Board, you will need to tie
TxE and RxF together on the RS-232 header at J14 as
shown in the diagram.
The Dynamic C STDIO window will display the error
sequence.
J14
TxE RxE GND TxF RxF 485+ GND 485
J14
TxE RxE GND TxF RxF 485+ GND 485
相關PDF資料
PDF描述
20-101-1131 MODULE RCM4200 RABBITCORE
20-101-1139 RCM4310 RABBITCORE
20-101-1154 MODULE RCM4120 RABBITCORE
20-101-1197 MODULE RABBITCORE RCM3910 ROHS
20-101-1215 MCU RCM4050 RABBITCORE
相關代理商/技術參數
參數描述
20-101-1087 制造商:Digi International 功能描述:RCM3365 RABBITSYS - Bulk 制造商:Digi International Inc 功能描述:BOARD PROTO RCM3365 RS232 制造商:Rabbit Semiconductor 功能描述:RCM3365 Rabbit Sys
20-101-1093 功能描述:模塊化系統 - SOM RCM4110 RABBIT CORE MODULE RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1094 功能描述:模塊化系統 - SOM RCM4000 Coremodule RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1095 功能描述:模塊化系統 - SOM BL2600 XD HOT SWAP 10/100 RoHS:否 制造商:Digi International 外觀尺寸:ConnectCore 9P 處理器類型:ARM926EJ-S 頻率:150 MHz 存儲容量:8 MB, 16 MB 存儲類型:NOR Flash, SDRAM 接口類型:I2C, SPI, UART 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 尺寸:1.97 in x 1.97 in x 6.1 in
20-101-1104 功能描述:處理器配件 USB xd reader RoHS:否 制造商:Olimex Ltd. 產品:Cable 用于:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*