參數資料
型號： 20-101-0383
廠商： Rabbit Semiconductor
文件頁數： 68/80頁
文件大小： 0K
描述： MODULE RABBITCORE RCM2020
標準包裝： 1
系列： RabbitCore®
模塊/板類型： MPU 核心模塊
適用于相關產品： RCM2020
產品目錄頁面： 620 (CN2011-ZH PDF)
其它名稱： 316-1082
66
RabbitCore RCM2000
C.2 Chip Select Circuit
Figure C-4 shows a schematic of the chip select circuit.
Figure C-4. Chip Select Circuit
The current drain on the battery in a battery-backed circuit must be kept to a minimum.
When the RCM2000 is not powered, the battery keeps the SRAM memory contents and
the real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control circuit accomplishes this task for the CS signal line.
In a powered-up condition, the CS control circuit must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be battery voltage high). Q13 and Q14 are MOSFET transistors with
opposing polarity. They are both turned on when power is applied to the circuit. They
allow the CS signal to pass from the processor to the SRAM so that the processor can peri-
odically access the SRAM. When power is removed from the circuit, the transistors will
turn off and isolate /CSRAM from the processor. The isolated /CSRAM line has a 100 k
pullup resistor to VRAM (R28). This pullup resistor keeps /CSRAM at the VRAM voltage
level (which under no-power conditions is the backup battery’s regulated voltage at a little
more than 2 V).
Transistors Q13 and Q14 are of opposite polarity so that a rail-to-rail voltages can be
passed. When the /CS1 voltage is low, Q13 will conduct. When the /CS1 voltage is high,
Q14 will conduct. It takes time for the transistors to turn on, creating a propagation delay.
This delay is typically very small, about 10 ns to 15 ns.
/CS1
/CSRAM
/RES
Q10
Q13
Q14
R15
R28
VRAM
22 kW
C6
R5
100 kW
1 nF
相關PDF資料
PDF描述
AT25128N-10SI-2.7 IC EEPROM 128KBIT 3MHZ 8SOIC
345-030-523-201 CARDEDGE 30POS DUAL .100 GREEN
345-030-521-802 CARDEDGE 30POS DUAL .100 GREEN
AT25128-10PI-2.7 IC EEPROM 128KBIT 3MHZ 8DIP
345-030-521-804 CARDEDGE 30POS DUAL .100 GREEN
相關代理商/技術參數
參數描述
20-101-0389 功能描述:子卡和OEM板 SR9200 16IN/8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0390 功能描述:子卡和OEM板 SR9210 8 in/ 16 out RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0391 功能描述:子卡和OEM板 SR9220 DIG I/O 8IN 8OUT RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0392 功能描述:子卡和OEM板 SR9300 A/D 0-10V RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
20-101-0393 功能描述:子卡和OEM板 SR9400 D/A CARD RoHS:否 制造商:BeagleBoard by CircuitCo 產品:BeagleBone LCD4 Boards 用于:BeagleBone - BB-Bone - Open Source Development Kit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*