- 您現在的位置：買賣IC網 > PDF目錄2021 > 19635 (Desco)TESTER MINIMEG 9VDC NIST PDF資料下載
參數資料
| 型號： | 19635 |
| 廠商： | Desco |
| 文件頁數： | 2/4頁 |
| 文件大小： | 0K |
| 描述： | TESTER MINIMEG 9VDC NIST |
| 標準包裝： | 1 |
| 系列： | Micro Meg™ |
| 類型： | 表面電阻測量?jī)x |
| 使用： | 測量表面電阻系數、接地電阻 |
| 特點： | NIST 溯源 |
| 電源類型： | 9V 電池 |
| 包括： | 電池，軟線 |
TB-2083 Page 2 of 4
Each LED indicates one order of magnitude of
resistance. If the test surface is conductive to less than
10E5, all the LEDs will be lit. If it is neither conductive
nor static dissipative, only the red “On” LED will be lit.
Surface Resistivity Measurements
Surface resistivity measurements are made using only
the meter without the cord assembly. When the white
button is depressed a test voltage of 9 VDC is applied
to the meter’s center electrode. The second resistivity
electrode will supply the resistance bridge and provide
the measurement. To perform surface resistivity tests,
follow these simple instructions:
A. Check battery operation by depressing the white
button on the center of the megohmmeter. The red
“On” lamp at the far right should light to indicate that
the unit is functioning properly.
B. Place the meter on the surface being tested. All
three electrodes should make contact with the surface.
C. Press the white button. The surface resistance will
be indicated by the number of LEDs which light up.
The more lights illuminated, the greater the conductivity
of the surface. The measurement is in ohms/square.
Figure 3. Measuring surface resistivity.
Surface-to-Ground Measurements (RTG)
The Surface-to-Ground feature is best used when
expected results are less than 10E6 ohms, and
when residual voltages can be removed from the test
surface. Residual voltages may cause the two upper
range LEDs to light, resulting in a false reading.
When the Surface-to-Ground cord is plugged in,
voltage is diverted from the center electrode to the
cord in order to measure resistance. When making
Surface-to-Ground tests, follow these procedures:
A. Check battery operation by depressing the white
button. The red “On” lamp will indicate that the unit is
functioning properly.
B. Plug the Surface-to-Ground cord into the left side of
the megohmmeter.
Figure 4. Installing Surface-to-Ground cord assembly.
C. Place the Micro Meg on the test surface.
D. Connect the test cord to the ground-point for the
surface.
E. Press the white button. The LEDs will indicate the
test results. The measurement is in ohms.
GROUND
POINT
WORK SURFACE
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178 Fax (909) 627-7449
DESCO EAST
- One Colgate Way, Canton, MA 02021-1407 (781) 821-8370 Fax (781) 575-0172 Web Site: Desco.com
2010 DESCO INDUSTRIES INC.
Employee Owned
Figure 5. Measuring Surface-to-Ground resistance.
F. Unplug the cord when testing is finished.
Battery Operation
Battery function is automatically checked by the unit
when the meter is turned on. If the battery voltage
drops below 8 VDC, the red LED on the far right of the
meter will not light, indicating a “l(fā)ow battery” condition.
Replace battery with a new 9V alkaline battery.
Maintenance
Your Micro Meg will require very little maintenance,
and there are few user-serviceable parts. If your
meter requires service beyond the simple procedures
described below please contact the factory.
Electrode Cleaning
To assure accurate measurements the electrodes
should be kept as clean as possible. A thorough
cleaning at least every 3 months is recommended. The
following is the recommended cleaning procedure:
1. Carefully remove the electrodes from their
snap-jacks using a screw driver or other blunt flat
bladed object. Avoid scratching or bending electrodes.
相關PDF資料 |
PDF描述 |
|---|---|
| 19665 | MONITOR DUAL WIRE CONTINOUS 120V |
| 19780 | KIT METER RES DIG TEMP/HUMIDITY |
| 19784 | TEST KIT SURFACE RESISTANCE |
| 19851 | WRIST STRAP DUAL ASSY 12' CORD |
| 19859 | WRISTSTRAP DUAL ASSY MTL EXP 4MM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1963-5 | 制造商:VIDEK 功能描述:PATCH LEAD EXT UTP 5M 制造商:VIDEK 功能描述:PATCH LEAD, EXT UTP, 5M 制造商:VIDEK 功能描述:PATCH LEAD, EXT UTP, 5M; Connector Type A:RJ45 Plug; Connector Type B:RJ45 Socket; Cable Length - Imperial:16ft; Cable Length - Metric:5m; Jacket Colour:Grey; Cable Assembly Type:Network; Cable Length:5m; Colour:Beige; Lead ;RoHS Compliant: Yes 制造商:VIDEK 功能描述:PATCH LEAD, EXT UTP, 5M; Connector Type A:RJ45 Plug; Connector Type B:RJ45 Socket; Cable Length - Imperial:16.4ft; Cable Length - Metric:5m; Jacket Colour:Grey; Cable Assembly Type:Network; Cable Length:5m; Colour:Beige; Lead ;RoHS Compliant: Yes |
| 1963-5 | 制造商:VIDEK 功能描述:PATCH LEAD EXT UTP 5M |
| 1963500000 | 制造商:Weidmuller 功能描述:CONN MOD JACK 8P8C SHIELDED 制造商:Weidmuller 功能描述:CAT6 RJ45 BULKHEAD CONN, 8POS, 1 PORT; Connector Type:RJ45; Series:SteadyTec; Gender:Jack; No. of Contacts:8; No. of Positions:8; No. of Ports:1; LAN Category:Cat6; Contact Termination:IDC / IDT ;RoHS Compliant: Yes |
| 1963502 | 功能描述:可插拔接線端子 2.5mm 10P R/A BLK RoHS:否 制造商:Phoenix Contact 產品:Plugs 系列:PTS 端接類型:Spring Cage 位置/觸點數量:5 線規量程:26-14 節距:5 mm 電流額定值:10 A 電壓額定值:250 V 安裝風格: 安裝角: 觸點電鍍: |
| 196350400 | 制造商:DANAHER - TEKTRONIX 功能描述:LEAD,ELEC, 1 INCH SOLDER DOWN |
發布緊急采購，3分鐘左右您將得到回復。