- 您現在的位置：買賣IC網 > PDF目錄7038 > 16282 (Desco)MAT DISS VINYL BLUE .100 36X40' PDF資料下載
參數資料
| 型號： | 16282 |
| 廠商： | Desco |
| 文件頁數： | 1/4頁 |
| 文件大?。?/td> | 0K |
| 描述： | MAT DISS VINYL BLUE .100 36X40' |
| 其它有關文件： | Mat Selection Chart |
| MSDS 材料安全數據表： | Static Dissipative Type B MSDS |
| 標準包裝： | 1 |
| 系列： | STATFREE B™ |
| 墊子類型： | 桌子，工作臺卷筒 |
| 形狀： | 矩形 |
| 長度： | 40'（12.19m） |
| 寬： | 3'（0.91m） |
| 厚度： | 0.10"（2.54mm） |
| 顏色： | 藍 |
| 材質： | 乙烯基 |
| 特點： | 耗散 |
TB-2000 March 2012 Page 1 of 4
Installation and
Maintenance of ESD Mats
Introduction
The purpose of an ESD worksurface is to aid in the prevention
of damage to ESD sensitive components and assemblies from
electrostatic discharge. An ESD worksurface provides protection in
the following two ways:
1. Providing an antistatic worksurface area that will limit static
electricity generation.
2. Removing the charge from a conductive object placed on the
worksurface.
A dissipative worksurface having a surface resistance of at
least 1 x 10E6, but less than 1 x 10E9 ohms is recommended
by worksurface standard ANSI/ESD S4.1. Dissipative materials
minimize the generation of static charges, and will dissipate a
charge slow enough so that a spark will not occur. Dissipative
materials are usually the preferred choice for bench top
worksurfaces.
Conductive materials are the quickest to remove a charge,
but they can also cause damage by discharging too rapidly.
Conductive materials are usually used as floor mats, which is
defined by ANSI/ESD S7.1 as less than 1 x 10E6 ohms.
General Grounding Guidelines
1. ANSI/ESD S20.20 requires that all conductors in an ESD
protected area, including personnel, must be grounded.
2. The ESD ground must be tied directly to and at the same
potential as the building or “green wire” equipment ground.
3. Per ANSI/ESD S20.20, the ESD control program can in no
way replace or supercede any requirements for personnel
safety. Ground fault circuit interrupters (GFCI) and other safety
protection should be considered wherever personnel might
come into contact with electrical sources.
4. All electrical outlets should be verified for proper wiring
configuration, resistance or impedance and GFCI function when
the mat is installed and periodically thereafter.
Common Point Grounds
A common point ground is defined by the grounding standard
ANSI/ESD S6.1, as:
1. A grounded device where two or more conductors are bonded.
2. A system or method for connecting two or more grounding
conductors to the same electrical potential.
Examples of common point grounds with ground cords are
illustrated below.
Figure 2. Other ground cords.
Figure 3. 09814 with screw allows ground cord to be bolted to mat
to keep cord from disconnecting.
Common point grounds are designed to provide ground for
worksurface mats, wrist straps, and other items.
NOTE: DO NOT DAISY CHAIN. Because of the high resistances
inherent to many types of protective surfaces, daisy chaining of
these materials can severely limit their ability to properly dissipate
and protect against static charges.
DESCO WEST
- 3651 Walnut Avenue, Chino, CA 91710 (909) 627-8178
DESCO EAST - One Colgate Way
, Canton, MA 02021-1407 (781) 821-8370 Web Site: Desco.com
TECHNICAL BULLETIN TB-2000
Made in the
United States of America
2012 DESCO INDUSTRIES INC.
Employee Owned
Figure 1. Typical common point grounds.
COMMON POINT GROUND
Per ANSI/ESD S6.1, Grounding section 4.1.1 “Every element to be
grounded at an ESD protected station shall be connected to the
same common point ground.”
ESD Handbook ESD TR20.20 section 5.1.3 Basic Grounding
Requirements “The first step in ensuring that everything in an
EPA is at the same electrical potential is to ground all conductive
components of the work area (worksurfaces, people, equipment,
etc.) to the same electrical ground point. This point is called the
common point ground. The next step in completing the ground
circuit is to connect the common point ground to the equipment
ground (third wire, green).”
WRONG!
RIGHT
Figure 4. ESD mats should never be grounded in series, that is
daisy chained.
相關PDF資料 |
PDF描述 |
|---|---|
| 433610-25-0 | TERM BARRIER 25CIRC 1 ROW .4375 |
| 433603-25-0 | TERM BARRIER 25CIRC 1 ROW .4375 |
| 433602-25-0 | TERM BARRIER 25CIRC 1 ROW .4375 |
| 433315-25-0 | TERM BARRIER 25CIRC 1 ROW .4375 |
| 433310-25-0 | TERM BARRIER 25CIRC 1 ROW .4375 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 1628-2 | 功能描述:支架與墊片 .109" SWAGE THREADED STANDOFF RoHS:否 制造商:Schurter 類型:Transipillar Spacers 長度:16 m 螺紋大小:M4 外徑:10 mm 材料:Nylon with Steel 電鍍:Zinc |
| 1628200000 | 功能描述:CONN PCB BLZ 7.50 8POS OR RoHS:是 類別:連接器，互連式 >> 接線座 - 接頭，插頭和插口 系列:Omnimate BLZ 產品培訓模塊:BLF Push-In Connector Technology PCB Connection Technology 產品目錄繪圖:BLF Series 5.08/270F 特色產品:BLF Pluggable PCB Connectors 標準包裝:24 系列:Omnimate BLF 端接塊類型:插頭，母插口 每電平位置:12 間距:0.200"（5.08mm） 級別數目:1 接頭定向:- 插頭導線入口:270° 端子:無螺絲 － 按入式 線規:12-26 AWG 電流:10A 電壓:300V 安裝類型:自由懸掛 特點:法蘭，固定鎖（非導線側） 顏色:黑 包裝:散裝 產品目錄頁面:336 (CN2011-ZH PDF) 配套產品:1513660000-ND - CONN HDR 5.08MM 12POS 90 ORG1513610000-ND - CONN HDR 5.08MM 12POS 90 BLK1515960000-ND - CONN HDR 5.08MM 12POS 90 ORG281-1285-ND - CONN HEADER RT ANG 5.08MM 12POS 其它名稱:281-2711 |
| 1628201 | 功能描述:MOBILE AC CHARGING CABLE WITH VE 制造商:phoenix contact 系列:* 零件狀態:在售 標準包裝:1 |
| 16-2820-90C | 功能描述:IC 與器件插座 16P IC SOCKET RoHS:否 制造商:Molex 產品:LGA Sockets 節距:1.02 mm 排數: 位置/觸點數量:2011 觸點電鍍:Gold 安裝風格:SMD/SMT 端接類型:Solder 插座/封裝類型:LGA 2011 工作溫度范圍:- 40 C to + 100 C |
| 1628210000 | 功能描述:CONN PCB BLZ 7.50 9POS OR RoHS:是 類別:連接器，互連式 >> 接線座 - 接頭，插頭和插口 系列:Omnimate BLZ 其它有關文件:ED Part Number Breakdown 產品目錄繪圖:EDZ1200 Series Front EDZ1200 Series Side 標準包裝:50 系列:EDZ1200 端接塊類型:插頭，母插口 每電平位置:12 間距:0.200"（5.08mm） 級別數目:1 接頭定向:- 插頭導線入口:180° 端子:螺釘 線規:12-22 AWG 電流:15A 電壓:300V 安裝類型:自由懸掛 特點:固定鎖（非導線側） 顏色:綠 包裝:散裝 配套產品:EDSTLZ975/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-SW-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ975/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ970/12-F-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ955/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBEDSTLZ950/12-OE-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1859-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1827-ND - TERM BLOCK HDR 5.08MM 12POS PCBED1917-ND - TERM BLOCK HDR 5.08MM 12POS PCB 其它名稱:ED1993 |
發布緊急采購，3分鐘左右您將得到回復。