參數資料
型號： XCCACE-TQ144I
廠商： Xilinx Inc
文件頁數： 2/69頁
文件大?。?/td> 0K
描述： IC ACE CONTROLLER CHIP
產品變化通告： XCCACE-TQ144I Discontinuation 27/Feb/2006
標準包裝： 1
控制器類型： ACE 控制器
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 30mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 144-LQFP
供應商設備封裝： 144-TQFP（20x20）
包裝： 托盤
System ACE CompactFlash Solution
10
DS080 (v3.0) April 7, 2014
Product Specification
R
— OBSOLETE — OBSOLETE — OBSOLETE — OBSOLETE —
System ACE CF File Structure Requirements
The System ACE CF file structure must be on the first
partition of the CompactFlash device.
The System ACE CF partition must be formatted as
DOS FAT12 or FAT16.
The xilinx.sys file or single ACE file must be in
the root directory. The ACE file used only if
xilinx.sys
is not found. The xilinx.sys file
describes one collection directory with up to eight
subdirectories.
The xilinx.sys file must contain the line
dir=<dir_name>; where <dir_name> is the name of the
collection directory
The subsequent 8 lines of the xilinx.sys file must
consist of the lines cfgaddr<n>=<subdir_name>; where
<n> is 1 through 8 and <subdir_name> is the name of
a design sub-directory in the collection. In the case of
fewer than 8 designs in the collection, always start with
cfgaddr0 and only use contiguous cfgaddr locations.
Only one ACE file should exist in the ROOT directory
and/or in each \<dir>\<cfgaddr> folder pointed to
by the xilinx.sys file.
When sourcing from the MPU, the total length of the
ACE file must be a multiple of 32 bytes. Otherwise,
additional dummy bytes (1s or 0s) should be sent to
DATABUFREG to flush the last data buffer, allowing the
controller to correctly load the final commands in the
ACE file.
All directories accessed by the System ACE CF
controller must be formatted in a valid FAT 8.3 file
name format.
ACE file names can be up to eight characters long and
must include the .ace file extension.
All directories and ACE file names cannot contain
these reserved characters:
left angle bracket
<
right angle bracket
>
colon
:
quote mark
"
forward slash
/
back slash
\
pipe
|
The Partition Boot Record (PBR) for the first
CompactFlash partition that is used by the System
ACE CF controller must specify only one reserved
sector.
The CompactFlash card must be formatted with a
sector-per-cluster size greater than 1.
Other files and directories can coexist with System
ACE files and directories.
2 GB is the maximum capacity partition that the
System ACE CF controller can access using the FAT16
file system:
(65,535 clusters max) X (32 KB per cluster max)
= 2,147,123,200 bytes
2GB
16 MB is the maximum capacity partition that the
System ACE CF controller can access using the FAT12
file system:
(4,086 clusters max) X (4 KB per cluster max)
= 16,736,256 bytes
16 MB
System ACE CF Formatting Requirements
Three potential problem areas arise when formatting the CF
card for use with the System ACE CF controller:
1.
Sectors-per-Cluster Size
A CF card formatted with only one sector (512 bytes)
per cluster can cause problems for the System ACE CF
controller.
When the Windows OS formats the CF card, it uses a
formula to determine what it believes to be an optimal
sectors-per-cluster value, based on the size of the CF
partition and other factors. This can lead some
Windows OS versions to specify one sector (512 bytes)
per cluster in some CF configurations. For example, this
situation is known to occur when formatting 32 MB CF
cards with Windows 2000 and Windows XP. Disk
formatting utilities (such as mkdosfs, available from
avoid this situation.
2.
FAT12 or FAT16 Format
The System ACE CF controller does not recognize the
FAT32 file system. It was designed to recognize only the
FAT12 and FAT16 formats.
3.
Reserved Sectors
Reserved sectors are the sectors in the reserved region
of the volume starting at the first sector of the volume.
The System ACE CF controller can only read a CF card
that is formatted with one reserved sector in the
Partition Boot Record.
Specifying Sectors-per-Cluster and FAT Version
To correct the first two of these formatting issues, the CF
card should always be formatted with a sectors-per-cluster
size greater than 1 (UnitSize greater than 512), and the FAT
file system version should be specified. This can be done
using the format command with the
/fs:
and
/a:
options in this syntax:
format <volume> [/fs:<FileSystem>]
[/a:<UnitSize>]
For example:
format D: /FS:FAT /A:1024
相關PDF資料
PDF描述
VI-21W-IY-B1 CONVERTER MOD DC/DC 5.5V 50W
VE-21X-IY-B1 CONVERTER MOD DC/DC 5.2V 50W
VI-B1X-IY-B1 CONVERTER MOD DC/DC 5.2V 50W
V72A24C400B3 CONVERTER MOD DC/DC 24V 400W
V72A15C400BL2 CONVERTER MOD DC/DC 15V 400W
相關代理商/技術參數
參數描述
XCCACE-TQG144I 功能描述:IC ACE CONTROLLER CHIP TQ144 RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A
XCCAE7C13N 制造商:Schneider Electric 功能描述:ABSOLUTE ENCDER SINGLE TURN 13 BITS 11 30V DC 制造商:SCHNEIDER ELECTRIC 功能描述:ABSOLUTE ENCDER SINGLE TURN
XCC-C0 制造商:Excelsys Technologies 功能描述:ELECTRONIC PART
XCCN0000 制造商:Red Lion Controls 功能描述:OPTION CARD, DSP/MC CANOPEN OPTION CARD 制造商:Red Lion Controls 功能描述:DSP/MC CANOPEN OPTION CARD
XCCPM23121L10 制造商:Schneider Electric 功能描述:pre-wired M23 female connector - for incremental encoder - cable 10m 制造商:Schneider Electric 功能描述:Cable Assembly Pre-Wired Pigtail 10m 10 POS M23 Circular F
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*