參數資料
型號： ST72T121J4B6
元件分類： 8位微控制器
英文描述： 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
中文描述： 8位微控制器與2/4/8K字節在系統可編程閃存
文件頁數： 22/93頁
文件大?。?/td> 915K
代理商： ST72T121J4B6
22/93
ST72E121 ST72T121
POWER SAVING MODES
(Cont’d)
4.4.4 Halt Mode
The Halt mode is the MCU lowest power con-
sumption mode. The Halt mode is entered by exe-
cuting the HALT instruction. The internal oscillator
is then turned off, causing all internal processing to
be stopped, including the operation of the on-chip
peripherals. The Halt mode cannot be used when
the watchdog is enabled, if the HALT instruction is
executed while the watchdog system is enabled, a
watchdog reset is generated thus resetting the en-
tire MCU.
When entering Halt mode, the I bit in the CC Reg-
ister is cleared so as to enable External Interrupts.
If an interrupt occurs, the CPU becomes active.
The MCU can exit the Halt mode upon reception of
an interrupt or a reset. Refer to the Interrupt Map-
ping Table. The oscillator is then turned on and a
stabilization time is provided before releasing CPU
operation. The stabilization time is 4096 CPU clock
cycles.
After the start up delay, the CPU continues oper-
ation by servicing the interrupt which wakes it up or
by fetching the reset vector if a reset wakes it up.
Figure 17. HALT Flow Chart
N
N
EXTERNAL
INTERRUPT
1)
RESET
HALT INSTRUCTION
4096 CPU CLOCK
CYCLES DELAY
FETCH RESET VECTOR
OR SERVICE INTERRUPT
CPU CLOCK
I-BIT
OSCILLATOR
PERIPH. CLOCK
2)
ON
OFF
ON
SET
CPU CLOCK
I-BIT
OSCILLATOR
PERIPH. CLOCK
OFF
OFF
OFF
CLEARED
Y
Y
WDG
ENABLED
N
Y
RESET
WATCHDOG
1) or some specific interrupts
2) if reset PERIPH. CLOCK = ON ; if interrupt
PERIPH. CLOCK = OFF
Note:
Before servicing an interrupt, the CC register is
pushed on the stack. The I-Bit is set during the inter-
rupt routine and cleared when the CC register is
popped.
CPU CLOCK
I-BIT
OSCILLATOR
PERIPH. CLOCK
ON
ON
ON
SET
22
相關PDF資料
PDF描述
ST72T121J4T6 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72121 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72121J2 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72121J4 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72171 8-BIT MCU WITH 8K FLASH. ADC. WDG. SPI. SCI. TIMERS SPGAS (SOFTWARE PROGRAMMABLE GAIN AMPLIFIERS). OP-AMP
相關代理商/技術參數
參數描述
ST72T121J4T6 功能描述:8位微控制器 -MCU OTP EPROM 16K SPI/SC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72T121J4T6S 制造商:STMicroelectronics 功能描述:
ST72T141K2B6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72T141K2M6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72T212G2B6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*