參數資料
型號: ST72T121J2B6
元件分類: 8位微控制器
英文描述: 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
中文描述: 8位微控制器與2/4/8K字節在系統可編程閃存
文件頁數: 65/93頁
文件大?。?/td> 915K
代理商: ST72T121J2B6
65/93
ST72E121 ST72T121
SERIAL PERIPHERAL INTERFACE
(Cont’d)
5.5.4 Functional Description
Figure 35
shows the serial peripheral interface
(SPI) block diagram.
This interface contains 3 dedicated registers:
– A Control Register (CR)
– A Status Register (SR)
– A Data Register (DR)
Refer to the CR, SR and DR registers in
Section
5.5.7
for the bit definitions.
5.5.4.1 Master Configuration
In a master configuration, the serial clock is gener-
ated on the SCK pin.
Procedure
– Select the SPR0 & SPR1 bits to define the se-
rial clock baud rate (see CR register).
– Select the CPOL and CPHA bits to define one
of the four relationships between the data
transfer and the serial clock (see
Figure 38
).
– The SS pin must be connected to a high level
signal during the complete byte transmit se-
quence.
– The MSTR and SPE bits must be set (they re-
main set only if the SS pin is connected to a
high level signal).
In this configuration the MOSI pin is a data output
and to the MISO pin is a data input.
Transmit sequence
The transmit sequence begins when a byte is writ-
ten the DR register.
The data byte is parallel loaded into the 8-bit shift
register (from the internal bus) during a write cycle
and then shifted out serially to the MOSI pin most
significant bit first.
When data transfer is complete:
– The SPIF bit is set by hardware
– An interrupt is generated if the SPIE bit is set
and the I bit in the CCR register is cleared.
During the last clock cycle the SPIF bit is set, a
copy of the data byte received in the shift register
is moved to a buffer. When the DR register is read,
the SPI peripheral returns this buffered value.
Clearing the SPIF bit is performed by the following
software sequence:
1. An access to the SR register while the SPIF bit
is set
2. A read to the DR register.
Note:
While the SPIF bit is set, all writes to the DR
register are inhibited until the SR register is read.
65
相關PDF資料
PDF描述
ST72T121J2T6 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72T121J4B6 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72T121J4T6 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72121 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72121J2 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
相關代理商/技術參數
參數描述
ST72T121J2T6 功能描述:8位微控制器 -MCU OTP EPROM 8K SPI/SCI RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72T121J2T6S 制造商:STMicroelectronics 功能描述:
ST72T121J4B6 功能描述:8位微控制器 -MCU OTP EPROM 16K SPI/SC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72T121J4T6 功能描述:8位微控制器 -MCU OTP EPROM 16K SPI/SC RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
ST72T121J4T6S 制造商:STMicroelectronics 功能描述: