參數資料
型號: ST72171
英文描述: 8-BIT MCU WITH 8K FLASH. ADC. WDG. SPI. SCI. TIMERS SPGAS (SOFTWARE PROGRAMMABLE GAIN AMPLIFIERS). OP-AMP
中文描述: 8位8K閃存微控制器。 ADC的。水分散粒劑。的SPI。脊髓損傷。定時器SPGAS(軟件可編程增益放大器)。運放
文件頁數: 16/93頁
文件大小: 915K
代理商: ST72171
16/93
ST72E121 ST72T121
3.2 RESET
3.2.1 Introduction
There are four sources of Reset:
– RESET pin (external source)
– Power-On Reset (Internal source)
– WATCHDOG (Internal Source)
– Low Voltage Detection Reset (internal source)
The Reset Service Routine vector is located at ad-
dress FFFEh-FFFFh.
3.2.2 External Reset
The RESET pin is both an input and an open-drain
output with integrated pull-up resistor. When one
of the internal Reset sources is active, the Reset
pin is driven low for a duration of t
RESET
to reset
the whole application.
3.2.3 Reset Operation
The duration of the Reset state is a minimum of
4096 internal CPU Clock cycles. During the Reset
state, all I/Os take their reset value.
A Reset signal originating from an external source
must have a duration of at least t
PULSE
in order to
be recognised. This detection is asynchronous
and therefore the MCU can enter Reset state even
in Halt mode.
At the end of the Reset cycle, the MCU may be
held in the Reset state by an External Reset sig-
nal. The RESET pin may thus be used to ensure
V
DD
has risen to a point where the MCU can oper-
ate correctly before the user program is run. Fol-
lowing a Reset event, or after exiting Halt mode, a
4096 CPU Clock cycle delay period is initiated in
order to allow the oscillator to stabilise and to en-
sure that recovery has taken place from the Reset
state.
In the high state, the RESET pin is connected in-
ternally to a pull-up resistor (R
ON
). This resistor
can be pulled low by external circuitry to reset the
device.
The RESET pin is an asynchronous signal which
plays a major role in EMS performance. In a noisy
environment, it is recommended to use the exter-
nal connections shown in
Figure 4
.
Figure 11. Reset Block Diagram
INTERNAL
RESET
WATCHDOG RESET
LOW VOLTAGE DETECTOR RESET
OSCILLATOR
SIGNAL
C
RESET
TO ST7
RESET
POWER-ON RESET
V
DD
R
ON
16
相關PDF資料
PDF描述
ST733C04LFL0 Fuse Holder; Fuse Size/Group:Micro; Mounting Type:PC Board; Body Material:Thermoplastic; Contact Material:Copper Alloy; Contact Plating:Tin; Current Rating:5A; Leaded Process Compatible:Yes; Terminal Type:Push-On
ST733C04LFM0 Fuse Holder; Leaded Process Compatible:Yes; Mounting Type:Panel Mount RoHS Compliant: Yes
ST733C08LFL0 Fuse Holder; Leaded Process Compatible:Yes; Mounting Type:Panel Mount RoHS Compliant: Yes
ST733C08LFM0 Automotive Fuse; Current Rating:3A; Voltage Rating:32V; Fuse Type:Fast Acting; Body Material:Plastic; Fuse Terminals:Blade; Length:15.41mm; Series:297; Voltage Rating:32V; Fuse Size/Group:15.41 x 10.92 x 3.81mm RoHS Compliant: Yes
ST7597 FUSE, 0.250A, 250V, 3AG SLO-BLO, CARTRIDGE
相關代理商/技術參數
參數描述
ST72171K2 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:REAL-TIME DEVELOPMENT TOOLS FOR THE ST7 MCU FAMILY
ST72212 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH 4 TO 8K ROM/OTP/EPROM, 256 BYTES RAM, ADC, WDG, SPI AND 1 OR 2 TIMERS
ST72212G2 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH 4 TO 8K ROM/OTP/EPROM, 256 BYTES RAM, ADC, WDG, SPI AND 1 OR 2 TIMERS
ST72212G2B1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH 4 TO 8K ROM/OTP/EPROM, 256 BYTES RAM, ADC, WDG, SPI AND 1 OR 2 TIMERS
ST72212G2B1/XXX 制造商:未知廠家 制造商全稱:未知廠家 功能描述:MICROCONTROLLER|8-BIT|ST72 CPU|CMOS|SDIP|32PIN|PLASTIC