參數資料
型號: ST72121J2
元件分類: 8位微控制器
英文描述: 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
中文描述: 8位微控制器與2/4/8K字節在系統可編程閃存
文件頁數: 35/93頁
文件大?。?/td> 915K
代理商: ST72121J2
35/93
ST72E121 ST72T121
16-BIT TIMER
(Cont’d)
16-bit Read Sequence:
(from either the Counter
Register or the Alternate Counter Register).
The user must read the MS Byte first, then the LS
Byte value is buffered automatically.
This buffered value remains unchanged until the
16-bit read sequence is completed, even if the
user reads the MS Byte several times.
After a complete reading sequence, if only the
CLR register or ACLR register are read, they re-
turn the LS Byte of the count value at the time of
the read.
Whatever the timer mode used (input capture, out-
put compare, One Pulse mode or PWM mode) an
overflow occurs when the counter rolls over from
FFFFh to 0000h then:
– The TOF bit of the SR register is set.
– A timer interrupt is generated if:
– TOIE bit of the CR1 register is set and
– I bit of the CC register is cleared.
If one of these conditions is false, the interrupt re-
mains pending to be issued as soon as they are
both true.
Clearing the overflow interrupt request is done in
two steps:
1.Reading the SR register while the TOF bit is set.
2.An access (read or write) to the CLR register.
Note:
The TOF bit is not cleared by accessing the
ACLR register. The advantage of accessing the
ACLR register rather than the CLR register is that
it allows simultaneous use of the overflow function
and reading the free running counter at random
times (for example, to measure elapsed time) with-
out the risk of clearing the TOF bit erroneously.
The timer is not affected by WAIT mode.
In HALT mode, the counter stops counting until the
mode is exited. Counting then resumes from the
previous count (MCU awakened by an interrupt) or
from the reset count (MCU awakened by a Reset).
5.3.3.2 External Clock
The external clock (where available) is selected if
CC0=1 and CC1=1 in the CR2 register.
The status of the EXEDG bit in the CR2 register
determines the type of level transition on the exter-
nal clock pin EXTCLK that will trigger the free run-
ning counter.
The counter is synchronised with the falling edge
of the internal CPU clock.
A minimum of four falling edges of the CPU clock
must occur between two consecutive active edges
of the external clock; thus the external clock fre-
quency must be less than a quarter of the CPU
clock frequency.
is buffered
Read
MS Byte
At t0
Read
LS Byte
Returns the buffered
LS Byte value at t0
At t0 +
t
Other
instructions
Beginning of the sequence
Sequence completed
LS Byte
35
相關PDF資料
PDF描述
ST72121J4 8-bit Microcontroller with 2/4/8K Bytes In-System Programmable Flash
ST72171 8-BIT MCU WITH 8K FLASH. ADC. WDG. SPI. SCI. TIMERS SPGAS (SOFTWARE PROGRAMMABLE GAIN AMPLIFIERS). OP-AMP
ST733C04LFL0 Fuse Holder; Fuse Size/Group:Micro; Mounting Type:PC Board; Body Material:Thermoplastic; Contact Material:Copper Alloy; Contact Plating:Tin; Current Rating:5A; Leaded Process Compatible:Yes; Terminal Type:Push-On
ST733C04LFM0 Fuse Holder; Leaded Process Compatible:Yes; Mounting Type:Panel Mount RoHS Compliant: Yes
ST733C08LFL0 Fuse Holder; Leaded Process Compatible:Yes; Mounting Type:Panel Mount RoHS Compliant: Yes
相關代理商/技術參數
參數描述
ST72121J4 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-BIT MICROCONTROLLER (MCU) WITH 8 TO 16 K ROM/OTP/EPROM. 384 TO 512 BYTES RAM. WDG. SCI. SPI & 2 TIMERS - SDIP42. TQFP44
ST72124J 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, ADC, 16-BIT TIMERS, SPI, SCI INTERFACES
ST72124J2 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, ADC, 16-BIT TIMERS, SPI, SCI INTERFACES
ST72124J2B 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, ADC, 16-BIT TIMERS, SPI, SCI INTERFACES
ST72124J2B1 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT MCU WITH SINGLE VOLTAGE FLASH MEMORY, ADC, 16-BIT TIMERS, SPI, SCI INTERFACES