- 您現在的位置：買賣IC網 > PDF目錄372303 > ST52F514F3M6 IC MAX 7000 CPLD 256 256-FBGA PDF資料下載
參數資料
| 型號： | ST52F514F3M6 |
| 英文描述： | IC MAX 7000 CPLD 256 256-FBGA |
| 中文描述： | 微控制器 |
| 文件頁數： | 32/106頁 |
| 文件大?。?/td> | 648K |
| 代理商： | ST52F514F3M6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
ST52F510/F513/F514
32/106
Figure 4.1 Commands and Data Communication Sequences
Programming mode start sequence
The generic procedure of commands execution,
with the data communication in both directions is
displayed in Figure 4.1.
Remark:
the Slave Address1010000 mustbe sent
after a Stop (i.e. each time the data direction
changes, to specifythe R/W bit). For example: if a
command to send data to the device has been
executed, a command for receiving data must be
followed bythe slaveaddress and theR/W bit must
be set to 1. The Programming Mode code doesn’t
need to be specified again .
Warning:
After entering the Programming Mode,
the currentlypointed address is the Page 48, Block
3, byte 0 (Lock Byte).
The
Programming Mode is showed in Table 4.2
list
of
the
available
commands
in
4.2.2 Fast Programming procedure.
The
fastest way to program the device memory is the
use ofthe FastBlockWritecommand. Thefollowing
procedure can be used to writethe memory with a
new program and new data, starting from the first
memory location:
1.
The Programming Mode is entered with the
sequence described above
2.
The memory is erased (all bits are put to 0)
with the GlobalErase command. The device
holds the SCL line low, releasing it after the
command is completed (about 2 ms). This
command also unlocks the device if locked.
3.
The FastBlockWrite command is sent and the
device acknowledges it
4.
The 32 bytes of data to be written in the first
memory Block are sent in a sequence. The
device acknowledges each of them
5.
After the device acknowledges the32nd byte,
it holds the SCL line until theparallel writing of
the 32 byte is completed (about 2.5 ms)
The Block Pointer is incremented by sending
the IncBlock command
The procedure is repeated from point 3 until
there is data to be sent to the memory
6.
7.
Note:
the Block Pointer assumes values between
0 to 7 (there are 8 blocks in a page). When the
Block Pointer is equal to 7, the IncBlock command
puts this pointer to 0 and increments the Page
Pointer. The Page Pointer, after page writing is
completed, does’t have to be incremented in the
procedure above described.
4.2.3 Random data writing.
A single byte can be
written in a specified memory location by using the
following procedure:
1.
The Programming Mode is entered with the
sequence described in Section 4.2.1
2.
The SetPage command is sent, followed by
the page number where the data should be
written
3.
The ByteWrite command is sent followed by
two bytes
4.
The firstbytes that follows the ByteWrite com-
mand is the address inside the pointed page
where the data must be written.
5.
The second byte is the data to be written
6.
The deviceheld theSCL line low until thedata
is not stored in the memory (about 4.5 ms: 2
ms for erasing and 2.5 for writing)
Execution of commands for writing data:
Execution of commands for reading data:
S=Start, P=Stop, A=Acknowledge, NA=Non-acknowledge
From Slave to Master
From Master to Slave
S
1010000
0
A
00000000
A
Command
A
Data1
A
.....
DataN
A
P
Command
A
Data1
A
.....
DataN
A
Command
A
Data1
A
.....
DataN
A
P
Command
A
Address
A
P
S
1010000
1
A
Data read NA
P
相關PDF資料 |
PDF描述 |
|---|---|
| ST52F514G0B6 | IC MAX 7000 CPLD 256 256-FBGA |
| ST52F514G0M6 | IC MAX 7000 CPLD 64 100-TQFP |
| ST52F514G1B6 | IC MAX 7000 CPLD 64 100-TQFP |
| ST52F514G1M6 | IC MAX 7000 CPLD 64 44-PLCC |
| ST52F514G3B6 | IC MAX 7000 CPLD 64 44-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST52F514FMB6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
| ST52F514FMM6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
| ST52F514G0B6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| ST52F514G0M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| ST52F514G1B6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。