- 您現在的位置：買賣IC網 > PDF目錄372303 > ST52F514F1B6 IC MAX 7000 CPLD 160 100-TQFP PDF資料下載
參數資料
| 型號： | ST52F514F1B6 |
| 英文描述： | IC MAX 7000 CPLD 160 100-TQFP |
| 中文描述： | 微控制器 |
| 文件頁數： | 34/106頁 |
| 文件大小： | 648K |
| 代理商： | ST52F514F1B6 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁
ST52F510/F513/F514
34/106
Figure 4.3 Reading and Erasing Procedures
Fast Reading Procedure
4.3 Memory Verify
To verify the memory contents or just to read part
of data stored in memory, the ByteRead and the
ReadData command can be used. The first
instruction needs the specification of the address;
the second one allows the sequential reading of
consecutive memory locations.
Since the device is “Slave” for the I
2
C protocol,
after receiving a command for reading, it must be
configured as Slave Transmitter to send the data.
In order to do so, the Slave Address (1010000)
must be sent again with the R/W byte set to 1, as
stated by the communication protocol.
4.3.1 Fast read procedure.
The memory can be
read sequentially by using the following procedure:
1.
The Programming mode is entered with the
sequence described in Section 4.2.1
2.
The pointers address the memory location 0
3.
The ReadData command is sent and the de-
vice acknowledges it.
4.
The Master generates a Stop condition fol-
lowed by a Start condition
5.
The Slave Address with the R/W byte set to 1
(10100001) is sent. The device receives the
Slave Address and acknowledges it.
The device sends the data to be read in the
serial data line SDA. The current absolute ad-
dress is post-incremented.
The Master device doesn’t send the acknowl-
edge and generates a stop condition.
To read the nextdata, the Master generates a
Start condition followed by theSlave Address
with the R/W byte set to 0 (10100000). The
device receives the Slave Address and ac-
knowledges it.
The sequence restartsfrom point 3 until there
is data to be read.
6.
7.
8.
9.
Remark:
for the same reasons explained in
Section 4.2.4 theOption Bytescannot beread with
this procedure: they can be read with a direct
addressing procedure as the one explained in the
next section.
Random Byte Reading Procedure
Byte Erasing Procedure
Block Erasing Procedure
S=Start, P=Stop, A=Acknowledge, NA=Non-acknowledge
From Slave to Master
From Master to Slave
S
10100000
A
00000000
A
ReadData
A
P
S
1010000
1
A
Data read NA
P
.....
.....
S
10100000
A
ReadData
A
P
S
1010000
1
A
Data read NA
P
.....
Data read NA
P
.....
SetPage
A
Page Address
A
ByteRead
A
Byte Address
A
P
S
1010000
1
A
.....
.....
Data read NA
P
S
1010000
0
A
Command
.....
.....
SetPage
A
Page Address
A
ByteErase
A
Byte Address
A
Command
.....
.....
SetPage
A
Page Address
A
IncBlock
A
.....
IncBlock
A
BlockErase
A
Command
.....
相關PDF資料 |
PDF描述 |
|---|---|
| ST52F514F1M6 | IC MAX 7000 CPLD 256 208-PQFP |
| ST52F514F3B6 | IC MAX 7000 CPLD 256 208-PQFP |
| ST52F514F3M6 | IC MAX 7000 CPLD 256 256-FBGA |
| ST52F514G0B6 | IC MAX 7000 CPLD 256 256-FBGA |
| ST52F514G0M6 | IC MAX 7000 CPLD 64 100-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ST52F514F1M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| ST52F514F3B6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| ST52F514F3M6 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| ST52F514FMB6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
| ST52F514FMM6 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:8-BIT INTELLIGENT CONTROLLER UNIT ICU Two Timer/PWMs, ADC, I2C, SPI, SCI |
發布緊急采購，3分鐘左右您將得到回復。