- 您現在的位置：買賣IC網 > PDF目錄374803 > SL1452 (Zarlink Semiconductor Inc.) WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV PDF資料下載
參數資料
| 型號： | SL1452 |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| 中文描述： | 寬帶線性調頻檢測儀衛星電視 |
| 文件頁數： | 4/8頁 |
| 文件大小： | 147K |
| 代理商： | SL1452 |
3
SL1452
1
2
p=
LC
SL1452 QUADRATURE DEMODULATOR
The SL1452 FM demodulator has a simple application with
very low external component count. This is demonstrated by the
applications circuit diagram Fig. 4, but as with most integrated
circuits, particularly those working at high frequencies, some
attention to good RF layout techniques and correct component
selection will ensure optimum results.
A good layout can usually be ensured by the simple precau-
tion of keeping all components close to the SL1452, maintaining
short lead lengths and ensuring a good low impedance ground
plane. Double sided board layout enables these objectives to be
easily met, but is not essential for satisfactory operation. All
coupling and decoupling capacitors should be chosen for low
impedance characteristics at high frequencies, multilayer ce-
ramic types usually providing small size and adequate high
frequency performance. For the quadrature coil tuning capacitor
a fairly stable component should be selected to prevent excessive
drift. The power supply decoupling capacitor from pin 6 to ground
should be 0.1
μ
F minimum but the input coupling and decoupling
values can be smaller, about 330pF being adequate.
The only remaining components to be selected are those
forming the quadrature circuit on pins 2 and 3 and some care in
the determination of values for these is required if maximum
performance is to be obtained.
First determine the quadrature circuit operating frequency,
which is a quarter of the input frequency on pin 8 due to the two
internal
4
2 stages (see Fig.2).
Choose suitable values for L and C to resonate at the correct
frequency using:
f =
The value of C should by greater than 15pF to prevent stray
capacitance effects introducing errors and distortion of the
demodulation curve, but the use of very large capacitances with
small inductance values will lower the impedance of the tuned
circuit at the required Q value, reducing the drive level to the
demodulator and thereby restricting the video output available.
In general, for operation in the 400MHz to 600MHz range, an
inductance value between 40nH and 60nH is recommended.
Once suitable L and C values have been determined, the
working Q for the quadrature circuit should be set, the Q value
determining the video output level and bandwidth. Video output
is proportional to Q whereas video bandwidth is inversely
proportional. The effect of Q variations on video bandwidth and
amplitude can be determined from Table 1 and the graphs in Fig. 5.
330
SL1452
4
3
2
1
5
6
7
8
0·04
μ
27p
1n
1
5V
0·1
μ
1n
VIDEO
OUTPUT
612MHz
INPUT
0V
A value for total damping resistor value to obtain the required
Q can be calculated from:
R = Q2
π
fL
The internal 800
resistance between pins 2 and 3 must be
allowed for when calculating R.
Example
Design a quadrature circuit to demodulate a carrier on pin 8
with centre frequency 480 MHz and video bandwidth of 10MHz.
For L = 40nH, f
= 120MHz,
C = 43·98pF (nearest preferred value 47pF)
From Table 1, Q required is approximately 6,
therefore total R required is:
R = Q2
π
fL
= 6
3
2
3
π
3
480
3
10
6
3
0·04
3
10
2
6
4
=181 ohms
Allowing for the internal 800
resistance between pins 2 and 3
(see Fig.3), the external resistance required is 234
. ; choose
270
.
It should be remembered that the internal 800
resistance is
subject to production tolerances and if fairly close control of
video bandwidth is required, the L and C ratio may require some
adjustment to ensure that the external R is sufficiently low to
swamp the effect of internal resistance changes. The value of
270
obtained in the example is low enough to allow adequate
control.
In order to overcome the effects of component tolerances, it
will usually be necessary to make either the L or C a variable
component, the value being adjusted to obtain best linearity.
Q
10
6
4
Bandwidth
7·5MHz
14MHz
23MHz
Table 1
Fig. 4 Typical application
相關PDF資料 |
PDF描述 |
|---|---|
| SL1452NADP | WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1452NAMP | WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1454 | WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1454NADP | WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1466 | Wideband PLL FM Demodulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SL1452NADP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1452NAMP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1454 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1454NADP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:WIDEBAND LINEAR FM DETECTOR FOR SATELLITE TV |
| SL1461 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:WIDEBAND PLL FM DEMODULATOR |
發布緊急采購，3分鐘左右您將得到回復。