- 您現在的位置：買賣IC網 > PDF目錄372106 > SA5778 (NXP Semiconductors N.V.) Serial triple gauge driver STGD PDF資料下載
參數資料
| 型號： | SA5778 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Serial triple gauge driver STGD |
| 中文描述： | 串行三規司機STGD |
| 文件頁數： | 8/16頁 |
| 文件大小： | 122K |
| 代理商： | SA5778 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
Philips Semiconductors
Product specification
SA5778
Serial triple gauge driver (STGD)
1998 Apr 03
8
SR01430
7
8
8
9
9
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3.0
2.5
2.0
1.5
1.0
0.5
0.0
125
150
175
235
325
1
POWER DISSIPATION FOR COIL
RESISTANCE IN OHMS AND OP-
ERATING BATTERY VOLTAGE
LOAD RESISTANCE
(
)
V
SWBATT
POWER
(W)
Figure 7.
Power Dissipation of the STGD as a Function of Coil Resistance and Operating Voltage
The STGD is specified to operate up to V
BATT
max. The over voltage
shutdown circuit will turn off the output buffers and the switched
battery supply when the battery voltage reaches V
OVSD.
Over
temperature conditions will also cause the output buffers to be
disabled.
The STGD employs a thermally enhanced SO-28 package. The
center four pins on each side are fused to the die pad to create a
path for removal of heat from the package to the copper foil on the
PC board. An area of copper foil is required on the PC board for
heat dissipation at higher power dissipation levels.
In order to determine the size of the copper foil required, both
thermal testing and thermal modeling were used. The effective
Θ
JA
(thermal resistance, junction to ambient) was determined using
both single and double sided PCBs with heat-sinking copper foil
areas. Figures 8 and 9 show the effect of PCB copper foil area on
the effective thermal resistance of the STGD part/PCB system.
Figure 8 shows the thermal resistance of the STGD mounted on a
PC board with heat-sinking copper on the component side only.
Figure 9 is a similar plot for a two sided PC board (same size copper
areas on each side). Both plots assume a 60 x 60 x 1.57 mm FR4
board with varying square-shaped sizes of 2 oz. copper. The two
sided board also assumes 8 thermal bias with 0.36 mm
2
cross
section.
It is important to note that at such a high ambient temperature (worst
case of 105
°
C assumed), radiation is just as significant as
convection in the dissipation of heat. Good radiation is highly
dependent on the emissivity of the heated surface, so the thermal
radiation properties of the copper foil should be considered. Bare,
clean copper is a good thermal conductor, but it has a low emissivity,
and is therefore a bad radiator. It is recommended that the copper
areas intended for heat dissipation be left covered with solder mask
or otherwise blackened to increase the emissivity, thereby improving
the heat radiating ability of the board.
相關PDF資料 |
PDF描述 |
|---|---|
| SA5778D | Serial triple gauge driver STGD |
| SA577 | Ceramic Multilayer Capacitor; Capacitance:6.8pF; Capacitance Tolerance:+/- 0.5 pF; Working Voltage, DC:50V; Dielectric Characteristic:C0G/NP0; Package/Case:0603; Series:VJ; Features:Multilayer Ceramic Chip Capacitor |
| SA577D | Unity gain level programmable power compandor |
| SA578 | Unity gain level programmable low power compandor |
| SA578D | Unity gain level programmable low power compandor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| SA5778D | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Serial triple gauge driver STGD |
| SA5778D,512 | 功能描述:緩沖器和線路驅動器 SERIAL TRIPLE GAUGE DRIVER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| SA5778D,518 | 功能描述:緩沖器和線路驅動器 SERIAL TRIPLE GAUGE DRIVER RoHS:否 制造商:Micrel 輸入線路數量:1 輸出線路數量:2 極性:Non-Inverting 電源電壓-最大:+/- 5.5 V 電源電壓-最小:+/- 2.37 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:MSOP-8 封裝:Reel |
| SA5778D/CE1804 | 制造商:NXP Semiconductors 功能描述:SERIAL TRIPLE GAUGE DRIVER 28-PIN SO |
| SA5778D/CE1804,512 | 功能描述:IC SERIAL TRPL GAUGE DRVR 28SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。