參數資料
型號: S29NS-P
廠商: Spansion Inc.
英文描述: MirrorBit Flash Family
中文描述: MirrorBit閃存系列
文件頁數: 40/86頁
文件大?。?/td> 2234K
代理商: S29NS-P
40
S29NS-P MirrorBit
TM
Flash Family
S29NS-P_00_A1 February 20, 2007
D a t a
S h e e t
( A d v a n c e
I n f o r m a t i o n )
to determine if the sector erase timer has timed out (See the section,
DQ3: Sector Erase Timeout State
Indicator
.) The time-out begins from the rising edge of the final WE# pulse in the command sequence.
When the Embedded Erase algorithm is complete, the bank returns to reading array data and addresses are
no longer latched. Note that while the Embedded Erase operation is in progress, the system can read data
from the non-erasing banks. The system can determine the status of the erase operation by reading DQ7 or
DQ6/DQ2 in the erasing bank. Refer to
Write Operation Status
for information on these status bits.
Once the sector erase operation has begun, only the Erase Suspend command is valid. All other commands
are ignored. However, note that a hardware reset immediately terminates the erase operation. If that occurs,
the sector erase command sequence should be reinitiated once that bank has returned to reading array data,
to ensure data integrity.
Figure 6.4
illustrates the algorithm for the erase operation. Refer to
Program/Erase Operations
for
parameters and timing diagrams.
Software Functions and Sample Code
The following is a C source code example of using the sector erase function. Refer to the
Spansion Low Level
Driver User’s Guide
(available on
www.spansion.com
) for general information on Spansion Flash memory
software development guidelines.
/* Example: Sector Erase Command */
*( (UINT16 *)base_addr + 0x555 ) = 0x00AA;
*( (UINT16 *)base_addr + 0x2AA ) = 0x0055;
*( (UINT16 *)base_addr + 0x555 ) = 0x0080;
*( (UINT16 *)base_addr + 0x555 ) = 0x00AA;
*( (UINT16 *)base_addr + 0x2AA ) = 0x0055;
*( (UINT16 *)sector_address )
/* write unlock cycle 1
/* write unlock cycle 2
/* write setup command
/* write additional unlock cycle 1 */
/* write additional unlock cycle 2 */
/* write sector erase command
*/
*/
*/
= 0x0030;
*/
Table 6.17
Sector Erase
(LLD Function = lld_SectorEraseCmd)
Cycle
Description
Operation
Byte Address
Word Address
Data
1
Unlock
Write
Base + AAAh
Base + 555h
00AAh
2
Unlock
Write
Base + 554h
Base + 2AAh
0055h
3
Setup Command
Write
Base + AAAh
Base + 555h
0080h
4
Unlock
Write
Base + AAAh
Base + 555h
00AAh
5
Unlock
Write
Base + 554h
Base + 2AAh
0055h
6
Sector Erase Command
Write
Sector Address
Sector Address
0030h
Unlimited additional sectors may be selected for erase; command(s) must be written within t
SEA
.
相關PDF資料
PDF描述
S29PL127N65GFWW02 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL127N 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL129N65GAWW02 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL129N65GAWW03 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
S29PL129N70GAW000 256/128/128 Mb (16/8/8 M x 16-Bit) CMOS, 3.0 Volt-only Simultaneous Read/Write, Page-Mode Flash Memory
相關代理商/技術參數
參數描述
S29PL032J 制造商:SPANSION 制造商全稱:SPANSION 功能描述:CMOS 3.0 Volt-only, Simultaneous Read/Write Flash Memory with Enhanced VersatileIO Control
S29PL032J55BAI120 制造商:Spansion 功能描述:NOR Flash Parallel 3V/3.3V 32Mbit 2M x 16bit 55ns 48-Pin FBGA Tray 制造商:Spansion 功能描述:FLASH PARALLEL - Trays
S29PL032J55BFI120 制造商:Spansion 功能描述:FLASH PARALLEL 3V/3.3V 32MBIT 2MX16 55NS 48FBGA - Trays
S29PL032J60BFI120 制造商:Spansion 功能描述:
S29PL032J60BFI120(E) 制造商:Spansion 功能描述:Cut Tape