參數資料
型號： P89LPC931A1FDH
廠商： NXP SEMICONDUCTORS
元件分類： 微控制器/微處理器
英文描述： 8-bit microcontroller with accelerated two-clock 80C51 core 4 kB-8 kB 3 V byte-erasable flash
中文描述： 8-BIT, FLASH, 18 MHz, MICROCONTROLLER, PDSO28
封裝： 4.40 MM, PLASTIC, MO-153, SOT-361, TSSOP-28
文件頁數： 33/66頁
文件大?。?/td> 1326K
代理商： P89LPC931A1FDH
P89LPC9301_931A1
All information provided in this document is subject to legal disclaimers.
NXP B.V. 2010. All rights reserved.
Product data sheet
Rev. 2 — 29 November 2010
39 of 66
NXP Semiconductors
P89LPC9301/931A1
8-bit microcontroller with accelerated two-clock 80C51 core
7.29.6 ICP
ICP is performed without removing the microcontroller from the system. The ICP facility
consists of internal hardware resources to facilitate remote programming of the
P89LPC9301/931A1 through a two-wire serial interface. The NXP ICP facility has made
in-circuit programming in an embedded application - using commercially available
programmers - possible with a minimum of additional expense in components and circuit
board area. The ICP function uses five pins. Only a small connector needs to be available
to interface your application to a commercial programmer in order to use this feature.
Additional details may be found in the P89LPC9301/931A1 User manual.
7.29.7 IAP
IAP is performed in the application under the control of the microcontroller’s firmware. The
IAP facility consists of internal hardware resources to facilitate programming and erasing.
The NXP IAP has made in-application programming in an embedded application possible
without additional components. Two methods are available to accomplish IAP. A set of
predefined IAP functions are provided in a Boot ROM and can be called through a
common interface, PGM_MTP. Several IAP calls are available for use by an application
program to permit selective erasing and programming of flash sectors, pages, security
bits, configuration bytes, and device ID. These functions are selected by setting up the
microcontroller’s registers before making a call to PGM_MTP at FF03H. The Boot ROM
occupies the program memory space at the top of the address space from FF00H to
FEFFH, thereby not conflicting with the user program memory space.
In addition, IAP operations can be accomplished through the use of four SFRs consisting
of a control/status register, a data register, and two address registers. Additional details
may be found in the P89LPC9301/931A1 User manual.
7.29.8 ISP
ISP is performed without removing the microcontroller from the system. The ISP facility
consists of a series of internal hardware resources coupled with internal firmware to
facilitate remote programming of the P89LPC9301/931A1 through the serial port. This
firmware is provided by NXP and embedded within each P89LPC9301/931A1 device. The
NXP ISP facility has made in-system programming in an embedded application possible
with a minimum of additional expense in components and circuit board area. The ISP
function uses five pins (VDD, VSS, TXD, RXD, and RST). Only a small connector needs to
be available to interface your application to an external circuit in order to use this feature.
7.29.9 Power-on reset code execution
The P89LPC9301/931A1 contains two special flash elements: the Boot Vector and the
Boot Status bit. Following reset, the P89LPC9301/931A1 examines the contents of the
Boot Status bit. If the Boot Status bit is set to zero, power-up execution starts at location
0000H, which is the normal start address of the user’s application code. When the Boot
Status bit is set to a value other than zero, the contents of the Boot Vector are used as the
high byte of the execution address and the low byte is set to 00H.
Table 8 shows the factory default Boot Vector setting for these devices. A factory-provided
bootloader is pre-programmed into the address space indicated and uses the indicated
bootloader entry point to perform ISP functions. This code can be erased by the user.
相關PDF資料
PDF描述
P89LPC930FDH 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM
P89LPC931FDH 8-bit microcontrollers with two-clock 80C51 core 4 kB-8 kB 3 V Flash with 256-byte data RAM
P89LPC9321FDH 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM
P89LPC932A1FDH 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM
P89LPC932A1FHN 8-bit microcontroller with accelerated two-clock 80C51 core 8 kB 3 V byte-erasable flash with 512-byte data EEPROM
相關代理商/技術參數
參數描述
P89LPC931A1FDH,512 功能描述:8位微控制器 -MCU IC 80C51 MCU FLASH 8K RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC931FDH 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontrollers with two-clock 80C51 core 4 kB/8 kB 3 V Flash with 256-byte data RAM
P89LPC931FDH,112 功能描述:8位微控制器 -MCU 80C51 8K FL 256B RAM RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC931FDH,129 功能描述:8位微控制器 -MCU 8K FL/256B RAM/I2C/SPI/TSSOP28 RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P89LPC931FDH.129 制造商:NXP Semiconductors 功能描述:IC 8BIT MCU 8K FLASH SMD 89LC931
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*