參數資料
型號： MT90823AB
廠商： ZARLINK SEMICONDUCTOR INC
元件分類： 路由/交換
英文描述： 3V Large Digital Switch
中文描述： TELECOM, DIGITAL TIME SWITCH, PQFP100
封裝： 14 X 14 MM, 1.40 MM HEIGHT, 0.50 MM PITCH, MS-026BED, LQFP-100
文件頁數： 13/46頁
文件大?。?/td> 663K
代理商： MT90823AB
MT90823
Data Sheet
13
Zarlink Semiconductor Inc.
Table 2 - Variable Throughput Delay Value
Table 3 - Constant Throughput Delay Value
For multiplexed operation, the 8-bit data and address (AD0-AD7), 8-bit Data (D8-D15), Address strobe/Address
latch enable (AS/ALE), Data strobe/Read (DS/RD), Read/Write /Write (R/W / WR), Chip select (CS) and Data
transfer acknowledge (DTA) signals are required. See Figure 13 and Figure 14 for multiplexed parallel microport
timing.
For the Motorola non-multiplexed bus, the 16-bit data bus (AD0-AD7, D8-D15), 8-bit address bus (A0-A7) and 4
control lines (CS, DS, R/W and DTA) signals are required. See Figure 15 for Motorola non- multiplexed microport
timing.
The MT90823 microport provides access to the internal registers, connection and data memories. All locations
provide read/write access except for the data memory and the frame alignment register which are read only.
Memory Mapping
The address bus on the microprocessor interface selects the MT90823 internal registers and memory. If the A7
address input is low, then the control (CR), interface mode selection (IMS), frame alignment (FAR) and frame input
offset (FOR) registers are addressed by A6 to A0 as shown in Table 4.
If the A7 address input is high, then the remaining address input lines are used to select up to 128 memory
subsection locations. The number selected corresponds to the maximum number of channels per input or output
stream. The address input lines and the stream address bits (STA) of the control register allow access to the entire
data and connection memories.
The control and IMS registers together control all the major functions of the device. The IMS register should be
programmed immediately after system power-up to establish the desired switching configuration (see “Serial Data
Interface Timing” and “Switching Configurations” ).
The control register controls switching operations in the MT90823. It selects the internal memory locations that
specify the input and output channels selected for switching.
Input Rate
Delay for Variable Throughput Delay Mode
(m - output channel number)
(n - input channel number))
m < n
m = n, n+1, n+2
m > n+2
2.048 Mb/s
32 - (n-m) time-slots
m-n + 32 time-slots
m-n time-slots
4.096 Mb/s
64 - (n-m) time-slots
m-n + 64 time-slots
m-n time-slots
8.192 Mb/s
128 - (n-m) time-slots
m-n + 128 time-slots
m-n time-slots
Input Rate
Delay for Constant Throughput Delay Mode
(m - output channel number)
(n - input channel number))
2.048 Mb/s
32 + (32 - n) + (m - 1) time-slots
4.096 Mb/s
64 + (64 - n) + (m- 1) time-slots
8.192 Mb/s
128 + (128 - n) + (m- 1) time-slots
相關PDF資料
PDF描述
MT90823AG 3V Large Digital Switch
MT90823AL 3V Large Digital Switch
MT90823AP 3V Large Digital Switch
MT90826 Quad Digital Switch
MT90826AG Quad Digital Switch
相關代理商/技術參數
參數描述
MT90823AB1 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 3.3V 100LQFP - Trays 制造商:Microsemi Corporation 功能描述:3V LARGE DIGITAL SWITCH 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH 2048X2048 100LQFP 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH 2048X2048 100LQFP
MT90823AG 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 3.3V 120BGA - Trays
MT90823AG2 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 3.3V 120BGA - Trays
MT90823AL 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 3.3V 100MQFP - Trays
MT90823AL1 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 3.3V 100MQFP - Trays 制造商:Microsemi Corporation 功能描述:PB FREE LOW VOLTAGE LARGE DIGITAL SWITCH 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH 2048X2048 100MQFP 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH 2048X2048 100MQFP
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*