- 您現在的位置：買賣IC網 > PDF目錄359234 > MT90820 (Zarlink Semiconductor Inc.) Large Digital Switch PDF資料下載
參數資料
| 型號： | MT90820 |
| 廠商： | Zarlink Semiconductor Inc. |
| 英文描述： | Large Digital Switch |
| 中文描述： | 大型數字開關 |
| 文件頁數： | 4/37頁 |
| 文件大?。?/td> | 573K |
| 代理商： | MT90820 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
MT90820
Data Sheet
4
Zarlink Semiconductor Inc.
Pin Description
Pin #
Name
Description
84
PLCC
100
MQFP
1, 11,
30, 54
64, 75
31, 41,
56, 66,
76, 99
V
SS
Ground.
2, 32,
63
5, 40,
67
V
DD
+5 Volt Power Supply.
3 - 10
68-75
STo8 - 15
ST-BUS Output 8 to 15 (Three-state Outputs):
Serial data Output stream. These
streams may have data rates of 2.048, 4.096 or 8.192 Mb/s, depending upon the value
programmed at bits DR0 - 1 in the IMS register.
12 - 27
81-96
STi0 - 15
ST-BUS Input 0 to 15 (Inputs):
Serial data input stream. These streams may have data
rates of 2.048, 4.096 or 8.192 Mb/s, depending upon the value programmed at bits DR0 -
1 in the IMS register.
28
97
F0i
Frame Pulse (Input):
When the WFPS pin is low, this input accepts and automatically
identifies frame synchronization signals formatted according to ST-BUS and GCI
specifications. When the WFPS pin is high, this pin accepts a negative frame pulse which
conforms to WFPS formats.
29
98
FE/HCLK
Frame Evaluation / HCLK Clock
(Input):
When the WFPS pin is low, this pin is the
frame measurement input. When the WFPS pin is high, the HCLK (4.096 MHz clock) is
required for frame alignment in the wide frame pulse (WFP) mode.
31
100
CLK
Clock (Input):
Serial clock for shifting data in/out on the serial streams (STi/o 0 - 15).
Depending upon the value programmed at bits DR0 - 1 in the IMS register, this input
accepts a 4.096, 8.192 or 16.384 MHz clock.
33
6
TMS
Test Mode Select (Input):
JTAG signal that controls the state transitions of the TAP
controller. This pin is pulled high by an internal pull-up when not driven.
34
7
TDI
Test Serial Data In (Input):
JTAG serial test instructions and data are shifted in on this
pin. This pin is pulled high by an internal pull-up when not driven.
35
8
TDO
Test Serial Data Out (Output):
JTAG serial data is output on this pin on the falling edge
of TCK. This pin is held in high impedance state when JTAG scan is not enable.
36
9
TCK
Test Clock (Input):
Provides the clock to the JTAG test logic. This pin is pulled high by
an internal pull-up when not driven.
37
10
TRST
Test Reset (Input):
Asynchronously initializes the JTAG TAP controller by putting it in
the Test-Logic-Reset state. This pin is pulled by an internal pull-up when not driven. This
pin should be pulsed low on power-up, or held low, to ensure that the MT90820 is in the
normal functional mode.
38
11
IC
Internal Connection (Input):
Connect to V
SS
for normal operation. This pin must be
low for the MT90820 to function normally and to comply with IEEE 1149 (JTAG)
boundary scan requirements. This pin is pulled low internally when not driven.
相關PDF資料 |
PDF描述 |
|---|---|
| MT90820AL | Large Digital Switch |
| MT90820AL1 | Large Digital Switch |
| MT90823AL1 | 3V Large Digital Switch |
| MT90823 | 3V Large Digital Switch |
| MT90823AB | 3V Large Digital Switch |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT90820AL | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 131.072MBPS 5V 100MQFP - Trays |
| MT90820AL1 | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 131.072MBPS 5V 100MQFP - Trays 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC DGTL SWITCH 2048X2048 100MQFP 制造商:Microsemi Corporation 功能描述:IC DGTL SWITCH 2048X2048 100MQFP |
| MT90820AP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Large Digital Switch |
| MT90820AP1 | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Large Digital Switch |
| MT90820APR | 制造商:Microsemi Corporation 功能描述:SWIT FABRIC 2K X 2K/1K X 1K/512 X 512 5V 84PLCC - Tape and Reel |
發布緊急采購，3分鐘左右您將得到回復。