- 您現在的位置：買賣IC網 > PDF目錄359234 > MT9043AN (ZARLINK SEMICONDUCTOR INC) T1/E1 System Synchronizer PDF資料下載
參數資料
| 型號： | MT9043AN |
| 廠商： | ZARLINK SEMICONDUCTOR INC |
| 元件分類： | 通信及網絡 |
| 英文描述： | T1/E1 System Synchronizer |
| 中文描述： | SPECIALTY TELECOM CIRCUIT, PDSO48 |
| 封裝： | 0.300 INCH, MO-118AA, SSOP-48 |
| 文件頁數： | 9/29頁 |
| 文件大小： | 453K |
| 代理商： | MT9043AN |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
MT9043
Data Sheet
9
Zarlink Semiconductor Inc.
As shown in Table 3, the Mode/Control Select pin MS selects the mode. Refer to Table 4 and Figure 7 for details of
the state change sequences.
Normal Mode
Normal Mode is typically used when a slave clock source, synchronized to the network is required.
In Normal Mode, the MT9043 provides timing (C1.5o, C2o, C4o, C8o, C16o and C19o) and frame synchronization
(F0o, F8o, F16o, TSP and RSP) signals, which are synchronized to one of two reference inputs (PRI or SEC). The
input reference signal may have a nominal frequency of 8kHz, 1.544MHz, 2.048MHz or 19.44MHz.
From a reset condition, the MT9043 will take up to 30 seconds (see AC Electrical Characteristics) of input reference
signal to output signals which are synchronized (phase locked) to the reference input.
The selection of input references is control dependent as shown in state table 4. The reference frequencies are
selected by the frequency control pins FS2 and FS1 as shown in Table 1.
Fast Lock Mode
Fast Lock Mode is a submode of Normal Mode, it is used to allow the MT9043 to lock to a reference more quickly
than Normal mode will allow. Typically, the PLL will lock to the incoming reference within 500 ms if the FLOCK pin is
set high.
Freerun Mode
Freerun Mode is typically used when a master clock source is required, or immediately following system power-up
before network synchronization is achieved.
In Freerun Mode, the MT9043 provides timing and synchronization signals which are based on the master clock
frequency (OSCi) only, and are not synchronized to the reference signals (PRI and SEC).
The accuracy of the output clock is equal to the accuracy of the master clock (OSCi). So if a
±
32ppm output clock
is required, the master clock must also be
±
32ppm. See Applications - Crystal and Clock Oscillator sections.
MT9043 Measures of Performance
The following are some synchronizer performance indicators and their corresponding definitions.
Intrinsic Jitter
Intrinsic jitter is the jitter produced by the synchronizing circuit and is measured at its output. It is measured by
applying a reference signal with no jitter to the input of the device, and measuring its output jitter. Intrinsic jitter may
also be measured when the device is free running by measuring the output jitter of the device. Intrinsic jitter is
usually measured with various bandlimiting filters depending on the applicable standards. In the MT9043, the
intrinsic Jitter is limited to less than 0.02UI on the 2.048MHz and 1.544MHz clocks.
Jitter Tolerance
Jitter tolerance is a measure of the ability of a PLL to operate properly (i.e., remain in lock and or regain lock in the
presence of large jitter magnitudes at various jitter frequencies) when jitter is applied to its reference. The applied
jitter magnitude and jitter frequency depends on the applicable standards.
Jitter Transfer
Jitter transfer or jitter attenuation refers to the magnitude of jitter at the output of a device for a given amount of jitter
at the input of the device. Input jitter is applied at various amplitudes and frequencies, and output jitter is measured
with various filters depending on the applicable standards.
相關PDF資料 |
PDF描述 |
|---|---|
| MT9043AN48PINSSOP | T1/E1 System Synchronizer |
| MT9045 | T1/E1/OC3 System Synchronizer |
| MT9045AN | T1/E1/OC3 System Synchronizer |
| MT9046 | T1/E1 System Synchronizer with Holdover |
| MT9046AN | T1/E1 System Synchronizer with Holdover |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MT9043AN1 | 制造商:Microsemi Corporation 功能描述:PB FREE T1/E1 SYSTEM SYNCHRONIZER 制造商:Microsemi Corporation 功能描述:FRAMER E1/T1 3.3V 48SSOP - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 48SSOP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 48SSOP |
| MT9043AN48PINSSOP | 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:T1/E1 System Synchronizer |
| MT9043ANR1 | 制造商:Microsemi Corporation 功能描述:FRAMER E1 /T1 3.3V 48SSOP - Tape and Reel 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC SYNCHRONIZER T1/E1 48SSOP 制造商:Microsemi Corporation 功能描述:IC SYNCHRONIZER T1/E1 48SSOP |
| MT9044 | 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:T1/E1/OC3 System Synchronizer |
| MT9044AL | 制造商:Microsemi Corporation 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays 制造商:Zarlink Semiconductor Inc 功能描述:FRAMER E1/OC3/T1 5V 44MQFP - Trays |
發布緊急采購，3分鐘左右您將得到回復。