參數(shù)資料
型號: MT8888CS
廠商: ZARLINK SEMICONDUCTOR INC
元件分類: 信令電路
英文描述: Integrated DTMF Transceiver with Intel Micro Interface
中文描述: TELECOM, DTMF SIGNALING CIRCUIT, PDSO20
封裝: 0.300 INCH, MS-013AC, SOIC-20
文件頁數(shù): 12/25頁
文件大?。?/td> 536K
代理商: MT8888CS
MT8888C
Data Sheet
12
Zarlink Semiconductor Inc.
11.0 DTMF Clock Circuit
The internal clock circuit is completed with the addition of a standard television color burst crystal. The crystal
specification is as follows:
Frequency:
3.579545 MHz
Frequency Tolerance:
±
0.1%
Resonance Mode:
Parallel
Load Capacitance:
18pF
Maximum Series Resistance: 150 ohms
Maximum Drive Level:
2mW
e.g.
CTS Knights MP036S
Toyocom
TQC-203-A-9S
A number of MT8888C devices can be connected as shown in Figure 13 such that only one crystal is required.
Alternatively, the OSC1 inputs on all devices can be driven from a TTL buffer with the OSC2 outputs left
unconnected.
Figure 13 - Common Crystal Connection
12.0 Microprocessor Interface
The MT8888C incorporates an Intel microprocessor interface which is compatible with fast versions (16 MHz) of the
80C51. No wait cycles need to be inserted.
Figure 19 and Figure 20 are the timing diagrams for the Intel 8031, 8051 and 8085 (5 MHz) microcontrollers. By
NANDing the address latch enable (ALE) output with the high-byte address (P2) decode output, CS is generated.
Figure 14 summarizes the connection of these Intel processors to the MT8888C transceiver.
The microprocessor interface provides access to five internal registers. The read-only Receive Data Register
contains the decoded output of the last valid DTMF digit received. Data entered into the write-only Transmit Data
Register will determine which tone pair is to be generated (see Table 1 for coding details). Transceiver control is
accomplished with two control registers (see Table 6 and Table 7), CRA and CRB, which have the same address. A
write operation to CRB is executed by first setting the most significant bit (b3) in CRA. The following write operation
to the same address will then be directed to CRB, and subsequent write cycles will be directed back to CRA. The
read-only status register indicates the current transceiver state (see Table 8).
A software reset must be included at the beginning of all programs to initialize the control registers upon power-up
or power reset (see Figure 19). Refer to Tables 4-7 for bit descriptions of the two control registers.
The multiplexed IRQ/CP pin can be programmed to generate an interrupt upon validation of DTMF signals or when
the transmitter is ready for more data (burst mode only). Alternatively, this pin can be configured to provide a
squarewave output of the call progress signal. The IRQ/CP pin is an open drain output and requires an external
pull-up resistor (see Figure 15).
MT8888C
OSC1
OSC2
MT8888C
OSC1
OSC2
MT8888C
OSC1
OSC2
3.579545 MHz
相關PDF資料
PDF描述
MT8888CP1 CB 5C 5#12 PIN RECP WALL
MT8888CN1 ER 5C 5#16S PIN RECP WALL
MT8888CPR Integrated DTMF Transceiver with Intel Micro Interface
MT8888CSR Integrated DTMF Transceiver with Intel Micro Interface
MT8888CSR1 Integrated DTMF Transceiver with Intel Micro Interface
相關代理商/技術參數(shù)
參數(shù)描述
MT8888CS1 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHz CMOS 5V 20-Pin SOIC Tube 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 20SOIC - Rail/Tube 制造商:MICROSEMI CONSUMER MEDICAL PRODUCT GROUP 功能描述:IC TXRX DTMF 20SOIC 制造商:Microsemi Corporation 功能描述:IC TXRX DTMF 20SOIC
MT8888CS-1 制造商:MITEL 制造商全稱:Mitel Networks Corporation 功能描述:Integrated DTMFTransceiver with Intel Micro Interface
MT8888CSR 制造商:Microsemi Corporation 功能描述:
MT8888CSR1 制造商:Microsemi Corporation 功能描述:DTMF TXRX 3.58MHZ CMOS 5V 20SOIC - Tape and Reel
MT8889C 制造商:ZARLINK 制造商全稱:Zarlink Semiconductor Inc 功能描述:Integrated DTMF Transceiver with Adaptive Micro Interface