- 您現在的位置：買賣IC網 > PDF目錄359201 > MPXY8040A (飛思卡爾半導體(中國)有限公司) Tire Pressure Monitoring Sensor, Temperature Compensated and Calibrated, Fully Integrated, Digital Output(輪胎壓力監控傳感器，具有溫度補償與校準、高度集成、數字輸出功能) PDF資料下載
參數資料
| 型號： | MPXY8040A |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Tire Pressure Monitoring Sensor, Temperature Compensated and Calibrated, Fully Integrated, Digital Output(輪胎壓力監控傳感器，具有溫度補償與校準、高度集成、數字輸出功能) |
| 中文描述： | 胎壓監測傳感器，溫度補償和校準，全集成，數字輸出（輪胎壓力監控傳感器，具有溫度補償與校準，高度集成，數字輸出功能） |
| 文件頁數： | 4/16頁 |
| 文件大小： | 381K |
| 代理商： | MPXY8040A |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
MPXY8000
4
Motorola Sensor Device Data
OUT Pin
The OUT pin normally provides a digital signal related to the
voltage applied to the voltage comparator and the threshold
level shifted into an 8-bit register from an external device. When
the device is placed in the standby mode the OUT pin is driven
high and will be clocked low when an overflow is detected from
a clock divider (divide by 16384) driven by the LFO. This allows
the OUT pin to wake up an external device such as an MCU.
Figure 3.
Pulse on
OUT Pin During Standby Mode
RST Pin
The RST pin is normally driven high and will be clocked low
when an overflow is detected from total clock divider (divide by
16,777,216) driven by the LFO. This allows the RST pin to reset
an external device such as an MCU. This pulse will appear on
the RST pin approximately every 52 minutes regardless of the
operating mode of the device. The pulse lasts for two cycles of
the LFO oscillator as shown in Figure 4. Since the RST pin is
clocked from the same divider string as the OUT pin, there will
also be a pulse on the OUT pin when the RST pin pulses every
52 minutes.
Figure 4. Pulse on RST Pin
S0 Pin
The S0 pin is used to select the mode of operation as shown
in Table 1.
The S0 pin contains an internal Schmitt trigger as part of its
input to improve noise immunity. The S0 pin has an internal pull-
down device in order to provide a low level when the pin is left
unconnected.
S1 Pin
The S1 pin is used to select the mode of operation, as shown
in Table 1.
The S1 pin contains an internal Schmitt trigger as part of its
input to improve noise immunity. This pin has an internal pull-
down device to provide a low level when the pin is left
unconnected.
The S1 pin also serves the purpose of enabling factory trim
and test of the device.
The higher V
programming voltage for the internal
EEPROM trim register is also supplied through the S1 pin.
DATA Pin
The DATA pin is the serial data in (SDI) function for setting
the threshold of the voltage comparator.
The DATA pin contains an internal Schmitt trigger as part of
its input to improve noise immunity. This pin has an internal pull-
down device to provide a low level when the pin is left
unconnected.
CLK Pin
The CLK pin is used to provide a clock used for loading and
shifting data into the DATA pin. The data on the DATA pin is
clocked into a shift register on the rising edge of the CLK pin
signal. The data is transferred to the D/A Register on the eighth
falling edge of the CLK pin. This protocol may be handled by the
SPI or SIOP serial I/O function found on some MCU devices.
The CLK pin contains an internal Schmitt trigger as part of its
input to improve noise immunity. The CLK pin has an internal
pull-down device to provide a low level when the pin is left
unconnected.
2/f
LFO
OUT
Operation
Wake Up
Measure
Standby
Measure
3 Sec
2/f
LFO
OUT
RST
Standby
≈
3 Sec
2/f
LFO
2/f
LFO
≈
52 Minutes
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料 |
PDF描述 |
|---|---|
| MPY534J | Precision ANALOG MULTIPLIER |
| MPY534K | Precision ANALOG MULTIPLIER |
| MPY534L | Precision ANALOG MULTIPLIER |
| MPY534S | Precision ANALOG MULTIPLIER |
| MPY534T | Precision ANALOG MULTIPLIER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPXY8040A6T1 | 功能描述:板上安裝壓力/力傳感器 TPMP 8-LD GULL WING RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXY8040A6U | 功能描述:板上安裝壓力/力傳感器 TPMP 8-LD GULL WING RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXY8300A6T1 | 功能描述:板上安裝壓力/力傳感器 Z-AXIS SOIC 20 RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXY8300A6U | 功能描述:板上安裝壓力/力傳感器 Z-AXIS SOIC 20 RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPXY8300B6T1 | 功能描述:板上安裝壓力/力傳感器 Z- AXIS FACE UP RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
發布緊急采購，3分鐘左右您將得到回復。