- 您現在的位置：買賣IC網 > PDF目錄359188 > MPC18730EP (飛思卡爾半導體(中國)有限公司) Power Management IC with Five Regulated Outputs Programmed Through 3 Wire Serial Interface PDF資料下載
參數資料
| 型號： | MPC18730EP |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | Power Management IC with Five Regulated Outputs Programmed Through 3 Wire Serial Interface |
| 中文描述： | 與電源管理IC，通過3線串行接口編程五穩壓輸出 |
| 文件頁數： | 14/35頁 |
| 文件大?。?/td> | 617K |
| 代理商： | MPC18730EP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
14
18730
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 18730 power management integrated circuit provides
five independent output voltages for the micro controller from
either a single cell Li-Ion or from a single cell Ni-MH or dry
cell. The PMIC includes two DC to DC converters and three
low drop out linear regulators. The output voltage for each of
the five output voltages is set independently through a 3-wire
serial interface. The PMIC has multiple wakeup, sleep, and
reset modes to minimize power consumption for portable
equipment. In single cell Li-Ion applications two DC-DC
converters are configured as buck regulators. In single cell
Ni-MH or dry cell applications, one DC-DC converter is
configured as a boost regulator, and the other as buck-boost
regulator.
FUNCTIONAL PIN DESCRIPTION
CLEAR PIN (CLEAR)
This Clear input signal makes clear internal latches for
WAKE signal holding. The WAKE control circuit can not
receive another WAKE input until the latch is cleared by this
Clear input.
WAKE SIGNAL PINS (WAKE1B, WAKE2B,
WAKE3B, WAKE4B) ... ACTIVE LOW
Any one WAKE input signal of these four WAKE inputs
awakes this device from sleep mode. The WAKE signals can
be made with external low side mechanical switch and
resistance that is pulled up to VSTB rail.
LOW-SIDE SWITCH OUTPUT PIN (LSWO)
Low-Side switch output that is turned on with ‘CLEAR’
signal. It can be used for external key input latches clear.
LOW VOLTAGE BATTERY PIN (LVB)
This input pin is used for temporarily power supply while
wake up for 1cell Ni-MH battery or 1 cell dry cell battery (=
Low Voltage Battery) use. It has to be connected to VB rail.
When Li-Ion battery is used, the pin has to be open.
HIGH VOLTAGE BATTERY PIN (HVB)
This input pin is used for temporarily power supply while
wake up for Li-Ion battery (= High Voltage Battery) use. It has
to be connected to the VB rail. When a Ni-MH battery is used,
the pin has to be connected to ground level.
STANDBY VOLTAGE PIN (V_STDBY)
Standby Voltage is made from LVB or HVB that depends
on which battery is used. This voltage is used for internal
logic and analog circuit at standby (sleep) mode temporarily
before ‘VO1_SENSE’ voltage is established.
VOLTAGE INPUT PINS (VO1_SENSE, VO2_SENSE)
This power supply input pin named ‘VO1_SENS or
VO2_SENSE’ is for internal logic and analog circuits and for
input of ‘VOUT1’ output via power switch. Input for ‘VOUT2’
is ‘VO2_SENSE_IN’ pin. It is supplied from the output of
Channel-1 or Channel-2 DC/DC converter as
‘VO1_SENSEor VO2_SENSE.
VOLTAGE OUTPUT PINS (VOUT1, VOUT2)
Output ‘VO1_SENSE or ‘VO2_SENSE’ voltage controlled
internal power switch.
POWER INPUT PINS (VIN1, VIN2)
The power input pins (VIN1, VIN2) are drain pins on the
top side FET of the DC/DC converter switcher. They are the
power input for the buck converter and output for the boost
converter.
SWITCHING PINS (SW1, SW2)
Switching Pins (SW1, SW2) are the output of the half
bridge and connect to the external inductance.
POWER GROUND PINS (PGND1, PGND2,
GNDGATE)
Ground level node for DC/DC converter and Charge Pump
portion.
INVERTED RESET OUTPUT PINS (PGOOD1,
PGOOD2)
Reset signal output for external MPU or the something
controller. PGOOD1 keeps ‘Low’ level while the
VO1_SENSE voltage is less than internal reference voltage.
PGOOD2 follows to VO2_SENSE voltage.
RESET DELAY CAPACITOR PINS
(PGOOD1_DELAY, PGOOD2_DELAY)
The capacitor connected to this pin decides delay time to
negate the Reset signal from exceeding the reference
voltage level.
RESET 1 ADJUSTMENT PIN (RESET1_TH)
Used to adjust the reset level with external resistance
which is connected to VO1_SENSE for PGOOD1.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC5200B | SDRAM/DDR Memory Controller |
| MPC5200 | Hardware Specifications |
| MPC5534 | Microcontroller |
| MPC7447A | PowerPC microprocessor |
| MPC7447ANXPNS | PowerPC microprocessor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC18730EP | 制造商:Freescale Semiconductor 功能描述:IC POWER MANAG PROG 121MA 64QFN |
| MPC18730EP/R2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Power Management IC with Five Power Management IC with Five Power Management IC with Five Power Management IC with Five |
| MPC18730EPR2 | 功能描述:板上安裝壓力/力傳感器 POWER MGT IC RoHS:否 制造商:Honeywell 工作壓力:0 bar to 4 bar 壓力類型:Gage 準確性:+ / - 0.25 % 輸出類型:Digital 安裝風格:Through Hole 工作電源電壓:5 V 封裝 / 箱體:SIP 端口類型:Dual Radial Barbed, Same sides |
| MPC18A26VMEL | 制造商:Motorola Inc 功能描述: |
| MPC190VMB | 制造商:Freescale Semiconductor 功能描述:IC SECURITY PROCESSOR 252-MAPBGA |
發布緊急采購，3分鐘左右您將得到回復。