- 您現在的位置：買賣IC網 > PDF目錄359187 > MPC17510MTB (飛思卡爾半導體(中國)有限公司) 1.2 A 15 V H-Bridge Motor Driver IC PDF資料下載
參數資料
| 型號： | MPC17510MTB |
| 廠商： | 飛思卡爾半導體(中國)有限公司 |
| 英文描述： | 1.2 A 15 V H-Bridge Motor Driver IC |
| 中文描述： | 1.2 15 V的H橋電機驅動芯片 |
| 文件頁數： | 8/14頁 |
| 文件大?。?/td> | 171K |
| 代理商： | MPC17510MTB |
Analog Integrated Circuit Device Data
Freescale Semiconductor
8
17510
FUNCTIONAL DESCRIPTION
INTRODUCTION
FUNCTIONAL DESCRIPTION
INTRODUCTION
The 17510 is a monolithic H-Bridge power IC applicable to
small DC motors used in portable electronics. The 17510 can
operate efficiently with supply voltages as low as 2.0 V to as
high as 15 V, and it can provide continuos motor drive
currents of 1.2 A while handling peak currents up to 3.8 A. It
is easily interfaced to low-cost MCUs via parallel 5.0 V-
compatible logic. The device can be pulse width modulated
(PWM-ed) at up to 200 kHz. The 17510 has four operating
modes: Forward, Reverse, Brake, and Tri-Stated (High
Impedance).
Basic protection and operational features (direction,
dynamic braking, PWM control of speed and torque, main
power supply undervoltage detection and shutdown, logic
power supply undervoltage detection and shutdown), in
addition to the 1.0 A rms output current capability, make the
17510 a very attractive, cost-effective solution for controlling
a broad range of small DC motors. In addition, a pair of 17510
devices can be used to control bipolar stepper motors. The
17510 can also be used to excite transformer primary
windings with a switched square wave to produce secondary
winding AC currents.
As shown in
Figure 2, 17510 Simplified Internal Block
Diagram
, page
2
, the 17510 is a monolithic H-Bridge with
built-in charge pump circuitry. For a DC motor to run, the
input conditions need to be set as follows: ENable input logic
HIGH, one INput logic LOW, and the other INput logic HIGH
(to define output polarity). The 17510 can execute dynamic
braking by setting both IN1 and IN2 logic HIGH, causing both
low-side MOSFETs in the output H-Bridge to turn ON.
Dynamic braking can also implemented by taking the ENable
logic LOW. The output of the H-Bridge can be set to an open-
circuit high-impedance (Z) condition by taking both IN1 and
IN2 logic LOW. (refer to
Table 5, Truth Table
, page
7
).
The 17510 outputs are capable of providing a continuous
DC load current of up to 1.2 A. An internal charge pump
supports PWM frequencies to 200 kHz. The EN pin also
controls the charge pump, turning it off when EN = LOW, thus
allowing the 17510 to be placed in a power-conserving sleep
mode.
FUNCTIONAL PIN DESCRIPTION
OUTPUT 1 AND OUTPUT2 (OUT1, OUT2)
The OUT1 and OUT2 pins provide the connection to the
internal power MOSFET H-Bridge of the IC. A typical load
connected between these pins would be a small DC motor.
These outputs will connect to either VM or PGND, depending
on the states of the control inputs (refer to
Table 5, Truth
Table
, page
7
).
POWER GROUND AND LOGIC GROUND (PGND,
LGND)
The power and logic ground pins (PGND and LGND)
should be connected together with a very low-impedance
connection.
CHARGE PUMP RESERVOIR CAPACITOR (CRES)
The CRES
pin provides the connection for the external
reservoir capacitor (output of the charge pump). Alternatively
this pin can also be used as an input to supply gate-drive
voltage from an external source via a series current-limiting
resistor. The voltage at the CRES pin will be approximately
three times the V
DD
voltage, as the internal charge pump
utilizes a voltage tripler circuit. The
VCRES
voltage is used by
the IC to supply gate drive for the internal power MOSFET
H-Bridge.
MOTOR SUPPLY VOLTAGE INPUT (VM)
The VM pins carry the main supply voltage and current into
the power sections of the IC. This supply then becomes
controlled and/or modulated by the IC as it delivers the power
to the load attached between OUT1 and OUT2. All VM pins
must be connected together on the printed circuit board with
as short as possible traces offering as low impedance as
possible between pins.
VM has an undervoltage threshold. If the supply voltage
drops below the undervoltage threshold, the output power
stage switches to a tri-state condition. When the supply
voltage returns to a level that is above the threshold, the
power stage automatically resumes normal operation
according to the established condition of the input pins.
CONTROL SIGNAL INPUT AND ENABLE CONTROL
SIGNAL INPUT (IN1, IN2, EN)
The IN1, IN2, and EN pins are input control pins used to
control the outputs. These pins are 5.0 V CMOS-compatible
inputs with hysteresis. The IN1, IN2, and EN work together to
control OUT1 and OUT2 (refer to
Table 5, Truth Table
).
GATE DRIVER INPUT (GIN)
The
GIN
input controls the GOUT pin. When
GIN
is set
logic LOW, GOUT supplies a level-shifted high-side gate
drive signal to an external MOSFET. When
GIN
is set logic
HIGH, GOUT is set to GND potential.
相關PDF資料 |
PDF描述 |
|---|---|
| MPC17510 | 1.2 A 15 V H-Bridge Motor Driver IC(1.2 A 15 V H橋電機驅動器IC) |
| MPC17511A | 1.0 A 6.8 V H-Bridge Motor Driver IC(1.0 A 6.8 V H橋電機驅動器IC) |
| MPC17517DTBR2 | 1.0 A 6.8 V Dual Motor Driver IC |
| MPC17517 | 1.0 A 6.8 V Dual Motor Driver IC |
| MPC17517DR2 | 1.0 A 6.8 V Dual Motor Driver IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MPC17510MTBEL | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:1.2 A 15 V H-Bridge Motor Driver IC |
| MPC17510R2 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:1.2 A 15 V H-Bridge Motor Driver IC |
| MPC17511 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:1 Channel H-Bridge Driver IC |
| MPC17511A | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:1.0 A 6.8 V H-Bridge Motor Driver IC |
| MPC17511AEL | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:1.0 A 6.8 V H-Bridge Motor Driver IC |
發布緊急采購，3分鐘左右您將得到回復。