- 您現在的位置：買賣IC網 > PDF目錄359168 > MK2058-01SITR Communications Clock Jitter Attenuator PDF資料下載
參數資料
| 型號： | MK2058-01SITR |
| 英文描述： | Communications Clock Jitter Attenuator |
| 中文描述： | 通信時鐘抖動衰減器 |
| 文件頁數： | 3/10頁 |
| 文件大?。?/td> | 150K |
| 代理商： | MK2058-01SITR |
Communications Clock Jitter Attenuator
MDS 2058-01 B
3
Revision 071001
Integrated Circuit Systems, Inc.
G
525 Race Street, San Jose, CA 95126
G
tel (408) 295-9800
G
www.icst.com
MK2058-01
Functional Description
The MK2058-01 is a clock generator IC that generates
an output clock directly from an internal VCXO circuit
which works in conjunction with an external quartz
crystal. The VCXO is controlled by an internal PLL
(Phase Locked Loop) circuit, enabling the device to
perform clock regeneration from an input reference
clock. The MK2058-01 is configured to provide an
output clock that is the same frequency as the input
clock. There are 12 selectable input / output frequency
ranges, each of which is a submultiple of the supported
quartz crystal frequency range. Please refer to the
Output Clock Selection Table on Page 2.
Most typical PLL clock devices use an internal VCO
(Voltage Controlled Oscillator) for output clock
generation. By using a VCXO with an external crystal,
the MK2058-01 is able to generate a low jitter, low
phase-noise output clock within a low bandwidth PLL.
This serves to provide input clock jitter attenuation and
enables stable operation with a low frequency
reference clock.
The VCXO circuit requires an external pullable crystal
for operation. External loop filter components enable a
PLL configuration with low loop bandwidth.
Application Information
Input / Output Frequency Configuration
The MK2058-01 is configured to generate an output
frequency that is equal to the input reference
frequency. Clock frequencies that are supported are
those which fall into the ranges listed in the Output
Clock Selection Table on Page 2. Input bits SEL2:0 are
set according to this table, as is the external crystal
frequency. The nominal (center) frequency of the
external crystal will be an integer multiple of the input /
output clock as specified. Please refer to the Quartz
Crystal section on this page regarding external crystal
requirements.
Input Mux
The Input Mux serves to select between two alternate
input reference clocks. Upon reselection of the input
clock, clock glitches on the output clock will not be
generated due to the “fly-wheel” effect of the VCXO
(the quartz crystal is a high-Q tuned circuit). When the
input clocks are not phase aligned, the phase of the
output clock will change to reflect the phase of the
newly selected input at a controlled phase slope (rate
of phase change) as influenced by the PLL loop
characteristics.
Quartz Crystal
It is important that the correct type of quartz crystal is
used with the MK2058-01. Failure to do so may result
in reduced frequency pullability range, inability of the
loop to lock, or excessive output phase jitter.
The MK2058-01 operates by phase-locking the VCXO
circuit to the input signal of the selected ICLK input.
The VCXO consists of the external crystal and the
integrated VCXO oscillator circuit. To achieve the best
performance and reliability, a crystal device with the
recommended parameters (shown below) must be
used, and the layout guidelines discussed in the PCB
Layout Recommendations section must be followed.
The frequency of oscillation of a quartz crystal is
determined by its cut and by the external load
capacitance. The MK2058-01 incorporates variable
load capacitors on-chip which “pull”, or change, the
frequency of the crystal. The crystals specified for use
with the MK2058-01 are designed to have zero
frequency error when the total of on-chip + stray
capacitance is 14pF. To achieve this, the layout should
use short traces between the MK2058-01 and the
crystal.
A complete description of the recommended crystal
parameters is shown below.
Recommended Crystal Parameters:
Operating Temperature Range
Commercial Applications
Industrial Applications
Initial Accuracy at 25
°
C
Temperature Stability
Aging
Load Capacitance
Shunt Capacitance, C0
C0/C1 Ratio
Equivalent Series Resistance
0 to 70
°
C
-40 to 85
°
C
±20 ppm
±30 ppm
±20 ppm
Note 1
7 pF Max
250 Max
35
Max
Note 1: For crystal frequencies between 13.5MHz and
27MHz the nominal crystal load capacitance
specification should be 14pF. Contact ICS MicroClock
applications at (408) 297-1201 regarding the use of a
crystal below 13.5MHz.
相關PDF資料 |
PDF描述 |
|---|---|
| MK2304S-2 | ZERO DELAY, LOW SKEW BUFFER |
| MK2308-2 | ZERO DELAY LOW SKEW BUFFER |
| MK2703SITR | PLL Audio Clock Synthesizer |
| MK2732-06GITR | Low Phase Noise VCXO+Multiplier |
| MK2732-06GTR | CONNECTOR ACCESSORY |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MK2059-01 | 制造商:ICS 制造商全稱:ICS 功能描述:VCXO-Based Frame Clock Frequency Translator |
| MK2059-01SI | 功能描述:IC VCXO CLK JITTER ATTEN 20-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
| MK2059-01SILF | 功能描述:時鐘合成器/抖動清除器 VCXO-BASED FRAME CLK FREQUENCY TRANSLATOR RoHS:否 制造商:Skyworks Solutions, Inc. 輸出端數量: 輸出電平: 最大輸出頻率: 輸入電平: 最大輸入頻率:6.1 GHz 電源電壓-最大:3.3 V 電源電壓-最小:2.7 V 封裝 / 箱體:TSSOP-28 封裝:Reel |
| MK2059-01SILFTR | 功能描述:時鐘發生器及支持產品 VCXO-BASED FRAME CLK FREQUENCY TRANSLATOR RoHS:否 制造商:Silicon Labs 類型:Clock Generators 最大輸入頻率:14.318 MHz 最大輸出頻率:166 MHz 輸出端數量:16 占空比 - 最大:55 % 工作電源電壓:3.3 V 工作電源電流:1 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-56 |
| MK2059-01SITR | 功能描述:IC VCXO CLK JITTER ATTEN 20-SOIC RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘發生器，PLL，頻率合成器 系列:- 標準包裝:39 系列:- 類型:* PLL:帶旁路 輸入:時鐘 輸出:時鐘 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 頻率 - 最大:170MHz 除法器/乘法器:無/無 電源電壓:2.375 V ~ 3.465 V 工作溫度:0°C ~ 70°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:* |
發布緊急采購，3分鐘左右您將得到回復。