參數資料
型號: MCZ33689DEWR2
廠商: Freescale Semiconductor
文件頁數: 13/31頁
文件大?。?/td> 0K
描述: IC SYSTEM BASIS CHIP LIN 32-SOIC
標準包裝: 1,000
應用: 自動
電流 - 電源: 5mA
電源電壓: 5.5 V ~ 18 V
工作溫度: -40°C ~ 125°C
安裝類型: 表面貼裝
封裝/外殼: 32-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 32-SOIC
包裝: 帶卷 (TR)
Analog Integrated Circuit Device Data
20
Freescale Semiconductor
33689
FUNCTIONAL DESCRIPTION
FUNCTIONAL PIN DESCRIPTION
RESET OUTPUT PIN (RST)
The RST pin is the 5.0 V regulator and Watchdog reset
output pin.
PWM INPUT CONTROL PIN (IN)
The IN pin is the external PWM control pin for the HS1 and
HS2 high-side switches.
SERIAL DATA CLOCK PIN (SCLK)
The SCLK pin is the SPI clock input pin. MISO data
changes on the negative transition of the SCLK. MOSI is
sampled on the positive edge of the SCLK.
MASTER OUT SLAVE IN PIN (MOSI)
The MOSI pin receives SPI data from the MCU. This data
input is sampled on the positive edge of SCLK.
MASTER IN SLAVE OUT PIN (MISO)
The MISO pin sends data to an SPI-enabled MCU. Data
on this output pin changes on the negative edge of the SCLK.
When CS is HIGH, this pin enters the high-impedance state.
CHIP SELECT PIN (CS)
The CS pin is the chip select input pin for SPI use. When
this signal is high, SPI signals are ignored. Asserting this pin
LOW starts an SPI transaction. The transaction is completed
when this signal returns HIGH.
INTERRUPT OUTPUT PIN (INT)
The INT pin is used to report 33689 faults to the MCU.
Interrupt pulses are generated for:
Voltage regulator temperature pre-warning
HS1, HS2, or HS3 thermal shutdown
VS1 or VS2 overvoltage (20 V typical)
VS1 or VS2 undervoltage (6.0 V typical)
If an interrupt is generated, then when the next SPI read
operation is performed bit D7 in the SPI Register will be set
to logic [1] and bits D6:D0 will report the interrupt source.
In cases of wake-up from the Stop mode, INT is set LOW
in order to signal to the MCU that a wake-up event from the
L1, L2, or LIN bus pin has occurred.
RECEIVER OUTPUT PIN (RXD)
The RXD pin is the receiver output of the LIN interface and
reports the state of the bus voltage (RXD LOW when LIN bus
is dominant, RXD HIGH when LIN bus is recessive).
TRANSMITTER INPUT PIN (TXD)
The TXD pin is the transmitter input of the LIN interface
and controls the state of the bus output (dominant when TXD
is LOW, recessive when TXD is HIGH).
GROUND PINS (GND, TGND, AND AGND)
The 33689 has three different types of ground pins.
The GND pin is the electrical ground pin for the device.
The AGND is the analog ground pin for the voltage
regulator and current sense operational amplifier.
The four TGND pins are the thermal ground pins for the
device.
Important The GND, the AGND, and the four TGND pins
must be connected together to a ground external to the
33689.
相關PDF資料
PDF描述
EEM28DRYH CONN EDGECARD 56POS DIP .156 SLD
EVAL-ADCMP553BRMZ BOARD EVALUATION ADCMP553BRMZ
ECM30DCAD CONN EDGECARD 60POS R/A .156 SLD
1025R-60K COIL 47.UH MOLDED UNSHIELDED
VI-BN0-EW CONVERTER MOD DC/DC 5V 100W
相關代理商/技術參數
參數描述
MCZ33730EK 功能描述:線性穩壓器 - 標準 SW MODE P/S W/ MULT REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
MCZ33730EK/R2 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Switch Mode Power Supply with Multiple Linear Regulators
MCZ33730EKR2 功能描述:線性穩壓器 - 標準 SW MODE P/S W/ MULT REG RoHS:否 制造商:STMicroelectronics 輸出類型: 極性: 輸出電壓:1.8 V 輸出電流:150 mA 負載調節: 最大輸入電壓:5.5 V 線路調整率: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOT-323-5L
MCZ33742EG 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray
MCZ33742EGR2 功能描述:網絡控制器與處理器 IC SBC-E-HS-CAN RoHS:否 制造商:Micrel 產品:Controller Area Network (CAN) 收發器數量: 數據速率: 電源電流(最大值):595 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:PBGA-400 封裝:Tray