參數資料
型號： MCP2140T-I/SS
廠商： Microchip Technology
文件頁數： 58/58頁
文件大?。?/td> 0K
描述： IC IRDA CONTROLLR DTE/DCE 20SSOP
標準包裝： 1,600
控制器類型： IRDA 標準協議棧控制器
接口： UART
電源電壓： 3 V ~ 5.5 V
電流 - 電源： 2.2mA
工作溫度： -40°C ~ 125°C
安裝類型： 表面貼裝
封裝/外殼： 20-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 20-SSOP
包裝： 帶卷 (TR)
配用： MCP2140DM-TMPSNS-ND - BOARD DEMO FOR MCP2140
2003 Microchip Technology Inc.
Preliminary
DS21790A-page 9
MCP2140
2.4
Host UART Interface
The Host UART interface communicates with the Host
Controller. This interface has eight signals associated
with it: TX, RX, RTS, CTS, DSR, DTR, CD and RI. Sev-
eral of these signals are locally generated (not passed
over the IR interface). The Host UART is a half-duplex
interface, meaning that the system is either transmitting
or receiving, but not both simultaneously.
2.4.1
BAUD RATE
The baud rate for the MCP2140 serial port (the TX and
RX pins) is fixed at 9600 baud when the device
frequency is 7.3728 MHz.
2.4.2
TRANSMITTING
When the controller sends serial data to the MCP2140,
the controller’s baud rate is required to match the baud
rate of the MCP2140’s serial port.
2.4.3
RECEIVING
When the controller receives serial data from the
MCP2140, the controller’s baud rate is required to
match the baud rate of the MCP2140’s serial port.
2.4.4
HARDWARE HANDSHAKING
There are three Host UART signals used to control the
handshaking operation between the Host Controller
and the MCP2140. They are:
DSR
RTS
CTS
2.4.4.1
DSR
The DSR signal is used to indicate that a link has been
established between the MCP2140 and the Primary
Device. Please refer to Section 2.13, “How Devices
Connect”, for information on how devices connect.
2.4.4.2
RTS
The RTS signal indicates to the MCP2140 that the Host
Controller is ready to receive serial data. Once an IR
data packet has been received, the RTS signal will be
low for the received data to be transferred to the Host
Controller. If the RTS signal remains high, an IR link
timeout will occur and the MCP2140 will disconnect
from the Primary Device.
2.4.4.3
CTS
The MCP2140 generates the CTS signal locally due to
buffer limitations.
The MCP2140 uses a 64-byte buffer for incoming data
from the IR Host. Another 29-byte buffer is provided to
buffer data from the UART serial port. The MCP2140
can handle IR data and Host UART serial port data
simultaneously. A hardware handshaking pin (CTS) is
provided to inhibit the Host Controller from sending
serial data when the Host UART buffer is not available
(Figure 2-3). Figure 2-4 shows a flow chart for Host
UART flow control using the CTS signal.
FIGURE 2-3:
HOST UART CTS SIGNAL AND THE RECEIVE BUFFER
Note 1: The MCP2140 generates several non-
data signals locally.
2: The MCP2140 emulates a 3-wire serial
connection (TXD, RXD and GND). The
transceiver’s
Transmit
Data
(TXD),
Receive Data (RXD) signals, and the
state of the CD. RI and DTR input pins
are carried back and forth to the Primary
device.
3: The RTS and CTS signals are local
emulations.
Note:
When the CTS output signal goes high, the
UART FIFO will store up to 6 bytes. This is
to allow devices that have a slow response
time to a change on the CTS signal time to
stop sending additional data (such as a
modem).
CTS
Receive Buffer Empty
MCP2140 Can Receive Data Receive Buffer Has 22 Bytes,
Receive Buffer
Receive Buffer Empty
MCP2140 Can Receive Data
IR Data Packet Transmitted
Full (29 Bytes)
CTS Pin Driven High
IR Data Packet Starts Transmission
相關PDF資料
PDF描述
MCP2140AT-I/SS IC IRDA CONTROLLR DTE/DCE 20SSOP
V150A15C400BF2 CONVERTER MOD DC/DC 15V 400W
V150A15C400BF CONVERTER MOD DC/DC 15V 400W
MCP2515-E/SO IC CAN CONTROLLER W/SPI 18SOIC
PIC12LCE519-04I/P IC MCU OTP 1KX12 LV W/EE 8DIP
相關代理商/技術參數
參數描述
MCP2150 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:DEVELOPER’S KIT USER’S GUIDE
MCP2150_13 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:IrDA?? Standard Protocol Stack Controller Supporting DTE Applications
MCP2150DM 功能描述:界面開發工具 MCP2150 Dev Board RoHS:否 制造商:Bourns 產品:Evaluation Boards 類型:RS-485 工具用于評估:ADM3485E 接口類型:RS-485 工作電源電壓:3.3 V
MCP2150-I/P 功能描述:輸入/輸出控制器接口集成電路 IrDA protocol handlr RoHS:否 制造商:Silicon Labs 產品: 輸入/輸出端數量: 工作電源電壓: 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-64 封裝:Tray
MCP2150-I/P 制造商:Microchip Technology Inc 功能描述:IC IRDA CONTROLLER 2150 DIP18
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*