參數資料
型號： MCIMX31
廠商： 飛思卡爾半導體(中國)有限公司
英文描述： Multimedia Applications Processors
中文描述： 多媒體應用處理器
文件頁數： 138/170頁
文件大?。?/td> 1562K
代理商： MCIMX31
i.MX31/i.MX31L Advance Information, Rev. 1.4
138
Freescale Semiconductor
Preliminary
Electrical Characteristics
4.3.20
SIM Electrical Specifications
Each SIM card interface consist of a total of 12 pins (for 2 separate ports of 6 pins each. Mostly one port
with 5 pins is used).
The interface is meant to be used with synchronous SIM cards. This means that the SIM module provides
a clock for the SIM card to use. The frequency of this clock is normally 372 times the data rate on the
TX/RX pins, however SIM module can work with CLK equal to 16 times the data rate on TX/RX pins.
There is no timing relationship between the clock and the data. The clock that the SIM module provides
to the aim card will be used by the SIM card to recover the clock from the data much like a standard UART.
All six (or 5 in case bi directional TXRX is used) of the pins for each half of the SIM module are
asynchronous to each other.
There are no required timing relationships between the pads in normal mode, but there are some in two
specific cases: reset and power down sequences.
4.3.20.1
General Timing Requirements
Figure 75
shows the timing of the SIM module, and
Figure 58
lists the timing parameters.
Figure 75. SIM Clock Timing Diagram
SDHC input / Card Outputs CMD, DAT (Reference to CLK)
SD8
Card Output Delay Time during Data Transfer
Mode
t
ODLY5
0
14
ns
Output Delay time during Identification Mode
t
ODLY6
0
50
ns
1
In low speed mode, card clock must be lower than 400 kHz, voltage ranges from 2.7 to 3.6 V.
2
In normal data transfer mode for SD/SDIO card, clock frequency can be any value between 0 ~ 25 MHz.
3
In normal data transfer mode for MMC card, clock frequency can be any value between 0 ~ 20 MHz.
4
In card identification mode, card clock must be l100 kHz ~ 400 kHz, voltage ranges from 2.7 to 3.6 V.
5
In identification mode, card output delay time should be less than 50 ns.
6
In data transfer mode, card output delay time should be less than 14 ns.
Table 57. SDHC Interface Timing Parameters (continued)
ID
Parameter
Symbol
Min
Max
Unit
CLK
Srise
Sfall
1/Sfreq
相關PDF資料
PDF描述
MCL245 SILICON EPITAXIAL PLANAR DIODE
MCL908QT1 M68HC08 Microcontrollers
MCM63R836 MCM63R836
MCN51-30S3-PFA 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
MCN51-30S3-DS 16 Characters x 2 Lines, 5x7 Dot Matrix Character and Cursor
相關代理商/技術參數
參數描述
MCIMX31_07 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors
MCIMX31_08 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors
MCIMX31_09 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Multimedia Applications Processors
MCIMX31ADSE 功能描述:KIT DEV ADS I.MX31 RoHS:是 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP
MCIMX31ADSE/C 功能描述:開發板和工具包 - ARM I.MX31 APP DEV SYS RoHS:否 制造商:Arduino 產品:Development Boards 工具用于評估:ATSAM3X8EA-AU 核心:ARM Cortex M3 接口類型:DAC, ICSP, JTAG, UART, USB 工作電源電壓:3.3 V
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*