參數資料
型號： MC33394
廠商： 飛思卡爾半導體(中國)有限公司
元件分類： CAN
英文描述： Switch Mode Power Supply with Multiple Linear Regulators and High Speed CAN Transceiver(帶有多個線性穩壓器和高速CAN收發器的開關方式電源)
中文描述： 開關電源的多線性穩壓器和高速CAN收發器（帶有多個線性穩壓器和高速的CAN收發器的開關方式電源）
文件頁數： 30/44頁
文件大?。?/td> 641K
代理商： MC33394
30
Go to: www.freescale.com
5.2.1.4. Selecting the Power MOSFET Q2
The boost converter maximum output voltage plus the
voltage drop across the output schottky rectifier D2 gives the
MOSFET’s maximum drain–source voltage stress:
BVdsQ2>Vo+Vfwd2 = 6 V+0.5 V, as can be seen, the
breakdown voltage parameter is not critical.
The more important in our case is the Q2 current handling
capability. The external power MOSFET has to withstand
higher currents than the upper current limit of the 33394:
IDQ2>3A
In order to keep the power dissipation of the 33394 boost
converter to its minimum, a very low RDSon power MOSFET
has to be selected. Moreover, due to the fact that the 33394
external MOSFET gate driver is supplied from VPRE, in
order to assure proper switching of Q2 a logic level device
has to be selected.
Last but not least, the Q2 package has to suitable for the
harsh automotive environment with low thermal resistance.
These requirements are met, for example by the
MTD20N03HDL power MOSFET from ON Semiconductor.
5.2.1.5. Selecting the Boost Converter Output
Rectifier D2
Criteria similar to that of selecting the power MOSFET was
used to select the boost converter output rectifier. Its reverse
breakdown voltage is not a critical parameter:
VrD2>Vo=6 V
The D2 rectifier has to withstand higher peak current than
is the 33394 internal switch upper current limit Ilim(max).
The most important parameter is its forward voltage drop,
which has to be minimal. This parameter is also crucial for the
proper 33394 switcher functionality, and especially for proper
transition between the buck and boost modes.
Finally, its switching speed, forward and reverse recovery
parameters play a significant role when selecting the output
rectifier D2.
These requirements are met, for example by the HSM350
schottky rectifier from Microsemi, Inc.
5.2.2. Input Filter Selection
Since the switcher will work in the Boost mode only during
cold crank condition, the 33394 EMC (electromagnetic
compatibility) performance is not of concern during this mode
of operation. Therefore, only the Buck mode of operation is
important for selecting the appropriate input filter. For the
Buck converter topology (see Figure 13) the low impedance
3rd order filter (C3, L2, C4 and C26 in the Application
Schematic Diagram Figure 20) offers a good solution. It can
be seen from the Buck converter current waveforms that
comparatively high current pulses are drawn from the
converter’s input source. The filter inductance must be kept
minimal and the capacitor, which is placed right next to the
power switch, must be sized large enough to provide
sufficient energy reservoir for proper switcher operation.
The ESR of this input capacitor combination C4, C26 has
to be sufficiently low to reduce the switching ripple of the
switcher input node VBAT. There are three main reasons to
keep the voltage ripple of the VBAT pin at its minimum. First,
it is the EMC (electromagnetic compatibility) performance of
the switcher in the normal operating mode (buck mode).
Second, it allows a smooth transition between the boost and
buck mode of operation. Third, it helps to avoid entering an
undervoltage condition too early. A practical way to achieve
sufficiently low ESR of the switcher input capacitor, even at
low temperature extremes, is to use several high value
ceramic capacitors in parallel with a large electrolytic
capacitor. These capacitors should be physically placed as
close to the VBAT pins as possible.
5.2.3. Buck Converter Feedback Compensation
A typical control loop of the buck regulator is shown in
Figure 17. The loop consists of a power processing block —
the modulator in series with an error–detecting block — the
Error (Feedback) Amplifier. In principle, a portion of the
output voltage (VPRE of the 33394 switcher) is compared to
a reference voltage (Vbg) in the Error Amplifier and the
difference is amplified and inverted and used as a control
input for the modulator to keep the controlled variable (output
voltage VPRE) constant.
Figure 17. The Buck Converter Control Loop
–
+
–
+
Zin
Zf
Reference
Voltage
ERROR FEEDBACK AMPLIFIER
MODULATOR
Vout
To Load
Ramp
PWM
Signal
Vin
Gain Block
(Modulator)
Feedback
Block
G
H
Vout
Vin
+
–
Vout/Vin = G/(1 + GH)
F
Freescale Semiconductor, Inc.
For More Information On This Product,
n
.
相關PDF資料
PDF描述
MC33395 Three-Phase Gate Driver IC(3相柵極驅動器)
MC33397 Dual/Hex Low-Side Switch with Both SPI and Parallel Input Control(帶SPI和并口輸入控制的2或6低端開關)
MC33399 “Local Interconnect Network” Physical Interface(“本地互聯網”（LIN）物理接口)
MC33486 Dual High Side Switch for H-Bridge Automotive Applications(適合于H橋自動應用的雙高端開關)
MC33661 LIN Enhanced Physical Interface(LIN網增強型物理接口)
相關代理商/技術參數
參數描述
MC33394DH 功能描述:IC POWER SUPPLY MULT-OUT 44-HSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
MC33395DWB 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395DWBR2 功能描述:馬達/運動/點火控制器和驅動器 TPD RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395EW 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
MC33395EWR2 功能描述:馬達/運動/點火控制器和驅動器 TPD - THREE PHASE DRIVER RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*