- 您現在的位置：買賣IC網 > PDF目錄24865 > 08056C103MAT2A (AVX Corporation) General Specifications PDF資料下載
參數資料
| 型號： | 08056C103MAT2A |
| 廠商： | AVX Corporation |
| 英文描述： | General Specifications |
| 中文描述： | 一般規格 |
| 文件頁數： | 9/20頁 |
| 文件大小： | 338K |
| 代理商： | 08056C103MAT2A |
57
Surface Mounting Guide
MLC Chip Capacitors
Component pads should be designed to achieve good
solder filets and minimize component movement during
reflow soldering. Pad designs are given below for the most
common sizes of multilayer ceramic capacitors for both
wave and reflow soldering. The basis of these designs is:
Pad width equal to component width. It is permissible to
decrease this to as low as 85% of component width but it
is not advisable to go below this.
Pad overlap 0.5mm beneath component.
Pad extension 0.5mm beyond components for reflow and
1.0mm for wave soldering.
D1
D2
D3
D4
D5
Case Size
D1
D2
D3
D4
D5
0402
1.70 (0.07)
0.60 (0.02)
0.50 (0.02)
0.60 (0.02)
0.50 (0.02)
0603
2.30 (0.09)
0.80 (0.03)
0.70 (0.03)
0.80 (0.03)
0.75 (0.03)
0805
3.00 (0.12)
1.00 (0.04)
1.25 (0.05)
1206
4.00 (0.16)
1.00 (0.04)
2.00 (0.09)
1.00 (0.04)
1.60 (0.06)
1210
4.00 (0.16)
1.00 (0.04)
2.00 (0.09)
1.00 (0.04)
2.50 (0.10)
1808
5.60 (0.22)
1.00 (0.04)
3.60 (0.14)
1.00 (0.04)
2.00 (0.08)
1812
5.60 (0.22)
1.00 (0.04))
3.60 (0.14)
1.00 (0.04)
3.00 (0.12)
1825
5.60 (0.22)
1.00 (0.04)
3.60 (0.14)
1.00 (0.04)
6.35 (0.25)
2220
6.60 (0.26)
1.00 (0.04)
4.60 (0.18)
1.00 (0.04)
5.00 (0.20)
2225
6.60 (0.26)
1.00 (0.04)
4.60 (0.18)
1.00 (0.04)
6.35 (0.25)
Dimensions in millimeters (inches)
REFLOW SOLDERING
WAVE SOLDERING
Component Spacing
For wave soldering components, must be spaced sufficiently
far apart to avoid bridging or shadowing (inability of solder
to penetrate properly into small spaces). This is less impor-
tant for reflow soldering but sufficient space must be
allowed to enable rework should it be required.
Preheat & Soldering
The rate of preheat should not exceed 4°C/second to
prevent thermal shock. A better maximum figure is about
2°C/second.
For capacitors size 1206 and below, with a maximum
thickness of 1.25mm, it is generally permissible to allow a
temperature differential from preheat to soldering of 150°C.
In all other cases this differential should not exceed 100°C.
For further specific application or process advice, please
consult AVX.
Cleaning
Care should be taken to ensure that the capacitors are
thoroughly cleaned of flux residues especially the space
beneath the capacitor. Such residues may otherwise
become conductive and effectively offer a low resistance
bypass to the capacitor.
Ultrasonic cleaning is permissible, the recommended
conditions being 8 Watts/litre at 20-45 kHz, with a process
cycle of 2 minutes vapor rinse, 2 minutes immersion in the
ultrasonic solvent bath and finally 2 minutes vapor rinse.
D1
D2
D3
D4
D5
Case Size
D1
D2
D3
D4
D5
0603
3.10 (0.12)
1.20 (0.05)
0.70 (0.03)
1.20 (0.05)
0.75 (0.03)
0805
4.00 (0.15)
1.50 (0.06)
1.00 (0.04)
1.50 (0.06)
1.25 (0.05)
1206
5.00 (0.19)
1.50 (0.06)
2.00 (0.09)
1.50 (0.06)
1.60 (0.06)
1210
5.00 (0.19)
1.50 (0.06)
2.00 (0.09)
1.50 (0.06)
2.50 (0.10)
Dimensions in millimeters (inches)
≥1mm (0.04)
≥1.5mm (0.06)
≥1mm (0.04)
Component Pad Design
相關PDF資料 |
PDF描述 |
|---|---|
| 08056C103MAT4A | General Specifications |
| 08056C103MAT7A | General Specifications |
| 08056C103MAT9A | General Specifications |
| 0805B102xxx | Multilayer Ceramic Chip Capacitors Products NPO, X7R, Y5V |
| 0805B104K500N | CERAMIC MULTILAYER CAPACITORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC10EP446FAG | 功能描述:串行到并行邏輯轉換器 3.3V/5V ECL 8-Bit Serial to Parallel RoHS:否 制造商:Supertex 工作電源電壓: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 封裝:Tray |
| MC10EP446FAR2 | 功能描述:串行到并行邏輯轉換器 3.3V/5V ECL 8-Bit RoHS:否 制造商:Supertex 工作電源電壓: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 封裝:Tray |
| MC10EP446FAR2G | 功能描述:串行到并行邏輯轉換器 3.3V/5V ECL 8-Bit Serial to Parallel RoHS:否 制造商:Supertex 工作電源電壓: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 封裝:Tray |
| MC10EP446MNG | 功能描述:串行到并行邏輯轉換器 BBG ECL PARALLEL T/SERIAL RoHS:否 制造商:Supertex 工作電源電壓: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 封裝:Tray |
| MC10EP446MNR4G | 功能描述:串行到并行邏輯轉換器 BBG ECL PARALLEL T/SERIAL RoHS:否 制造商:Supertex 工作電源電壓: 安裝風格:SMD/SMT 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。