- 您現在的位置：買賣IC網 > PDF目錄354173 > M28R400C-ZBU (意法半導體) 4 Mbit (256Kb x16, Boot Block) 1.8V Supply Flash Memory PDF資料下載
參數資料
| 型號： | M28R400C-ZBU |
| 廠商： | 意法半導體 |
| 英文描述： | 4 Mbit (256Kb x16, Boot Block) 1.8V Supply Flash Memory |
| 中文描述： | 4兆位（256Kb的x16插槽，引導塊）1.8V電源快閃記憶體 |
| 文件頁數： | 2/50頁 |
| 文件大?。?/td> | 755K |
| 代理商： | M28R400C-ZBU |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁
10/50
COMMAND INTERFACE
All Bus Write operations to the memory are inter-
preted by the Command Interface. Commands
consist of one or more sequential Bus Write oper-
ations. An internal Program/Erase Controller han-
dles all timings and verifies the correct execution
of the Program and Erase commands. The Pro-
gram/Erase Controller provides a Status Register
whose output may be read at any time during, to
monitor the progress of the operation, or the Pro-
Write State Machine Current/Next, for a summary
of the Command Interface.
The Command Interface is reset to Read mode
when power is first applied, when exiting from Re-
set or whenever VDD is lower than VLKO. Com-
mand sequences must be followed exactly. Any
invalid combination of commands will reset the de-
vice to Read mode. Refer to Table 3, Commands,
in conjunction with the text descriptions below.
Read Memory Array Command
The Read command returns the memory to its
Read mode. One Bus Write cycle is required to is-
sue the Read Memory Array command and return
the memory to Read mode. Subsequent read op-
erations will read the addressed location and out-
put the data. When a device Reset occurs, the
memory defaults to Read mode.
Read Status Register Command
The Status Register indicates when a program or
erase operation is complete and the success or
failure of the operation itself. Issue a Read Status
Register command to read the Status Register’s
contents. Subsequent Bus Read operations read
the Status Register at any address, until another
command is issued. See Table 10, Status Register
Bits, for details on the definitions of the bits.
The Read Status Register command may be is-
sued at any time, even during a Program/Erase
operation. Any Read attempt during a Program/
Erase operation will automatically output the con-
tent of the Status Register.
Read Electronic Signature Command
The Read Electronic Signature command reads
the Manufacturer and Device Codes and the Block
Locking Status, or the Protection Register.
The Read Electronic Signature command consists
of one write cycle, a subsequent read will output
the Manufacturer Code, the Device Code, the
Block Lock and Lock-Down Status, or the Protec-
the valid address.
Read CFI Query Command
The Read Query Command is used to read data
from the Common Flash Interface (CFI) Memory
Area, allowing programming equipment or appli-
cations to automatically match their interface to
the characteristics of the device. One Bus Write
cycle is required to issue the Read Query Com-
mand. Once the command is issued subsequent
Bus Read operations read from the Common
Flash Interface Memory Area. See Appendix B,
in the Common Flash Interface memory area.
Block Erase Command
The Block Erase command can be used to erase
a block. It sets all the bits within the selected block
to ’1’. All previous data in the block is lost. If the
block is protected then the Erase operation will
abort, the data in the block will not be changed and
the Status Register will output the error.
Two Bus Write cycles are required to issue the
command.
s
The first bus cycle sets up the Erase command.
s
The second latches the block address in the
internal state machine and starts the Program/
Erase Controller.
If the second bus cycle is not Write Erase Confirm
(D0h), Status Register bits b4 and b5 are set and
the command aborts.
Erase aborts if Reset turns to VIL. As data integrity
cannot be guaranteed when the Erase operation is
aborted, the block must be erased again.
During Erase operations the memory will accept
the Read Status Register command and the Pro-
gram/Erase Suspend command, all other com-
mands will be ignored. Typical Erase times are
given in Table 7, Program, Erase Times and Pro-
gram/Erase Endurance Cycles.
chart and Pseudo Code, for a suggested flowchart
for using the Block Erase command.
Chip Erase Command
The Chip Erase command can be used to erase
the entire chip. It sets all of the bits in unprotected
blocks of the memory to ’1’. All previous data is
lost. Two Bus Write operations are required to is-
sue the Chip Erase Command.
s
The first bus cycle sets up the Chip Erase
command.
s
The second confirms the Chip Erase command
and starts the Program/Erase Controller.
The command can be issued to any address. If
any blocks are protected then these are ignored
and all the other blocks are erased. If all of the
blocks are protected the Chip Erase operation ap-
pears to start but will terminate, leaving the data
unchanged. No error condition is given when pro-
tected blocks are ignored.
相關PDF資料 |
PDF描述 |
|---|---|
| M50FW080NB1 | CAP OXI NIOB 10UF 10V 20% SMD |
| M50FW080NB1G | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M50FW080NB1T | CAPACITOR, CASE A, 6.8UF, 10V; Application:Solid; Capacitance:6.8uF; Tolerance, capacitance:20%; Series:NOJ; Voltage, rating:10V; Capacitor dielectric type:Niobium Oxide; Case style:A; Depth, external:1.6mm; Length / Height, RoHS Compliant: Yes |
| M50FW080NB1TG | 8 Mbit 1Mb x8, Uniform Block 3V Supply Firmware Hub Flash Memory |
| M27C512-70XB1 | 512 Kbit (64K x8) UV EPROM and OTP EPROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M28S | 制造商:DCCOM 制造商全稱:Dc Components 功能描述:TECHNICAL SPECIFICATIONS OF NPN EPITAXIAL PLANAR TRANSISTOR |
| M28S_11 | 制造商:UTC-IC 制造商全稱:UTC-IC 功能描述:AUDIO OUTPUT DRIVER AMPLIFIER |
| M28S05/2000X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| M28S12/1000X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| M28S-B | 制造商:MCC 制造商全稱:Micro Commercial Components 功能描述:NPN Silicon Plastic-Encapsulate Transistor |
發布緊急采購，3分鐘左右您將得到回復。