- 您現在的位置：買賣IC網 > PDF目錄32307 > LM8500IMT9/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PDSO48 PDF資料下載
參數資料
| 型號： | LM8500IMT9/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 8/20頁 |
| 文件大小： | 327K |
| 代理商： | LM8500IMT9/NOPB |
14.0 Calibration (Continued)
Calibration, and Table 5. Thirteen Points Calibration respec-
tively.
TABLE 3. Two Points Calibration
Calibration point Theoretical X-value Theoretical Y-value
1
127
2
895
TABLE 4. Five Points Calibration
Calibration point Theoretical X-value Theoretical Y-value
1
127
2
895
3
127
895
4
511
5
895
127
TABLE 5. Thirteen Points Calibration
Calibration point Theoretical X-value Theoretical Y-value
1
127
2
895
3
127
895
4
511
5
895
127
6
895
511
7
511
895
8
127
511
9
511
127
10
623
319
11
623
12
319
623
13
319
14.1 GENERAL CALIBRATION PROCEDURES
Calibration is invoked by sending a command byte of $BD
followed by a command byte to the device. The command
byte is broken into two parts: the high nibble states the
number of calibration points to performs and the lower nibble
states the active calibration point. For example, to do the first
calibration point for the two point calibration, the command
bytes of $BD and $11 are sent to the device. The device then
echos $BD and $11 back to the TS driver and waits for a
touch on the panel. When a touch is detected, the device
checks to see if the point is within the specified parameters
if the calibration point checking is enabled. If the calibration
point checking is disabled, the device will send a $C8 for OK
byte to the TS driver regardless of where the touch was
detected. This calibration point checking can be enabled or
disabled by sending a command byte of $A5 to the device.
When all the calibration points are done, the device will do a
self-test and send a command of $CB for OK or a command
of $CC for failed. If a $CC is received, the TS driver should
issue a warning stating the calibration was not done properly
and redo the calibration procedures. The flowchart for the
calibration procedures is shown in Figure 8.
20037207
FIGURE 5. Two Points Calibration Mapping
20037208
FIGURE 6. Five Points Calibration Mapping
20037209
FIGURE 7. Thirteen Points Calibration Mapping
LM8300/LM8500
www.national.com
16
相關PDF資料 |
PDF描述 |
|---|---|
| LM8500HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LM8300HVA9/NOPB | SPECIALTY CONSUMER CIRCUIT, PQCC44 |
| LM8300IMT9/NOPB | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| LM8300HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LMF501T-2 | AM, AUDIO SINGLE CHIP RECEIVER, PBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8500IVA9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500-REF-01 | 功能描述:顯示開發工具 LM8500 DEV KIT RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
| LM8502 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。