- 您現在的位置：買賣IC網 > PDF目錄32307 > LM8500IMT9/NOPB (NATIONAL SEMICONDUCTOR CORP) SPECIALTY CONSUMER CIRCUIT, PDSO48 PDF資料下載
參數資料
| 型號： | LM8500IMT9/NOPB |
| 廠商： | NATIONAL SEMICONDUCTOR CORP |
| 元件分類： | 消費家電 |
| 英文描述： | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| 封裝： | TSSOP-48 |
| 文件頁數： | 7/20頁 |
| 文件大小： | 327K |
| 代理商： | LM8500IMT9/NOPB |
13.0 Brownout Reset (Continued)
The internal reset will not be turned off until t
id counts down
to zero. The internal reset will perform the same functions as
external reset. The device is guaranteed to operate at the
specified frequency down to the specified brownout voltage.
After the underflow, the logic is designed such that no addi-
tional internal resets occur as long as V
CC remains above
the brownout voltage.
The device is relatively immune to short duration negative
going V
CC transients (glitches). Proper filtering of the VCC
power supply voltage is essential for proper brownout func-
tionality. Power supply decoupling is vital even in battery
powered systems.
There are two optional brownout voltages. The part numbers
for the two versions of this device are:
LM8500, V
bor = high voltage range.
LM8300, V
bor = low voltage range.
Refer to the device specifications for the actual V
bor volt-
ages.
High brownout voltage devices are guaranteed to operate at
10MHz down to the high brownout voltage. Low brownout
voltage devices are guaranteed to operate at 3.33MHz down
to the low brownout voltage. Low brownout voltage devices
are not guaranteed to operate at 10MHz down to the low
brownout voltage.
Under no circumstances should the RESET pin be allowed
to float. The RESET input may be connected to an external
pull-up resistor to V
CC or to other external circuitry. The
output of the brownout reset detector will always preset t
id to
a value between 120-128s for the LM8500 and 360-384s
for the LM8300. At this time, the internal reset will be gener-
ated.
The device has a built in watchdog monitoring module to
prevent runaway code. To use the watchdog feature, the
WD_OUT pin must be connected to the RESET pin. The
WD_OUT pin has an internal weak pull-up so that, when the
WD_OUT pin is connected to the RESET pin, the RESET pin
does not require an external pull-up resistor to V
CC.
14.0 Calibration
The device supports two, five, and thirteen point calibration.
If desired, the calibration points can be stored internally in
the non-volatile storage element. During calibration time, the
device has the unique ability to check if the calibration points
make sense. For instance, if the desired calibration point
was to be at the upper left hand corner, but by accident, the
actual point detected was at the lower right hand corner, the
device will reject this point. This ensures the calibration
process is not performed incorrectly.
The calibration checking, can be enabled or disabled. If the
calibration checking is enabled, the controller will always
check the current calibration point being done against the
theoretical point and determine if the value is within ±127 of
the raw A/D values. If this option is desired, the touch screen
driver must perform the calibration according to the calibra-
tion mapping for the two, five, and thirteen points as shown
in Figure 5, Figure 6, and Figure 7, respectively. The theo-
retical values for the two, five, and thirteen points are shown
20037206
FIGURE 4. Brownout Reset Operation
LM8300/LM8500
www.national.com
15
相關PDF資料 |
PDF描述 |
|---|---|
| LM8500HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LM8300HVA9/NOPB | SPECIALTY CONSUMER CIRCUIT, PQCC44 |
| LM8300IMT9/NOPB | SPECIALTY CONSUMER CIRCUIT, PDSO48 |
| LM8300HLQ9/NOPB | SPECIALTY CONSUMER CIRCUIT, QCC44 |
| LMF501T-2 | AM, AUDIO SINGLE CHIP RECEIVER, PBCY3 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM8500IVA9 | 制造商:NSC 制造商全稱:National Semiconductor 功能描述:Four Wire Resistive Touchscreen Controller with Brownout |
| LM8500-REF-01 | 功能描述:顯示開發工具 LM8500 DEV KIT RoHS:否 制造商:4D Systems 產品:4Display Shields 工具用于評估:?OLED-160-G1, ?OLED-160-G2 接口類型:Serial 工作電源電壓:5 V |
| LM8502 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME | 制造商:TI 制造商全稱:Texas Instruments 功能描述:Intelligent Lighting Management Unit That Fuses a 1.2A Dual High-Side Flash LED Driver with a 10-Output Low-Side LED Driver |
| LM8502TME/NOPB | 功能描述:LED照明驅動器 RoHS:否 制造商:STMicroelectronics 輸入電壓:11.5 V to 23 V 工作頻率: 最大電源電流:1.7 mA 輸出電流: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:SO-16N |
發布緊急采購，3分鐘左右您將得到回復。