- 您現在的位置：買賣IC網 > PDF目錄11576 > KSZ8873MLL AM TR (Micrel Inc)IC ETHERNET SWITCH 3PORT 64LQFP PDF資料下載
參數資料
| 型號： | KSZ8873MLL AM TR |
| 廠商： | Micrel Inc |
| 文件頁數： | 29/115頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ETHERNET SWITCH 3PORT 64LQFP |
| 產品培訓模塊： | KSZ8873 Ethernet Switches |
| 標準包裝： | 1,000 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII |
| 電源電壓： | 1.8V，2.5V，3.3V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-PQFP（10x10） |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁
Micrel, Inc.
KSZ8873MLL/FLL/RLL
September 20, 2013
20
Revision 1.6
100BASE-FX Operation
100BASE-FX operation is similar to 100BASE-TX operation with the differences being that the scrambler/de-scrambler
and MLT3 encoder/decoder are bypassed on transmission and reception. In addition, auto-negotiation is bypassed and
auto MDI/MDI-X is disabled.
100BASE-FX Signal Detection
In 100BASE-FX operation, FXSD (fiber signal detect), input Pins 15 and 63, is usually connected to the fiber transceiver
SD (signal detect) output pin. The fiber signal threshold can be selected by Register 192 bit 7 and 6 respectively for port 2
and port 1, When FXSD is less than the threshold, no fiber signal is detected and a far-end fault (FEF) is generated.
When FXSD is over the threshold, the fiber signal is detected.
Alternatively, the designer may choose not to implement the FEF feature. In this case, the FXSD input pin is tied high to
force 100BASE-FX mode.
100BASE-FX signal detection is summarized in Table 1:
Table 1. FX Signal Threshold
Register 192 bit 7 (port 2), bit 6 (port 1)
Fiber Signal Threshold at FXSD
1
2.0V
0
1.2V
To ensure proper operation, a resistive voltage divider is recommended to adjust the fiber transceiver SD output voltage
swing to match the FXSD pin’s input voltage threshold.
100BASE-FX Far-End Fault
A far-end fault (FEF) occurs when the signal detection is logically false on the receive side of the fiber transceiver. The
KSZ8873FLL detects a FEF when its FXSD input is Fiber Signal Threshold. When a FEF is detected, the KSZ8873FLL
signals its fiber link partner that a FEF has occurred by sending 84 1’s followed by a zero in the idle period between
frames.
By default, FEF is enabled. FEF can be disabled through register setting.
10BASE-T Transmit
The 10BASE-T driver is incorporated with the 100BASE-TX driver to allow for transmission using the same magnetics.
They are internally wave-shaped and pre-emphasized into outputs with a typical 2.3V amplitude. The harmonic contents
are at least 27dB below the fundamental frequency when driven by an all-ones Manchester-encoded signal.
10BASE-T Receive
On the receive side, input buffers and level detecting squelch circuits are employed. A differential input receiver circuit and
a phase-locked loop (PLL) perform the decoding function. The Manchester-encoded data stream is separated into clock
signal and NRZ data. A squelch circuit rejects signals with levels less than 400mV or with short pulse widths to prevent
noise at the RXP-or-RXM input from falsely triggering the decoder. When the input exceeds the squelch limit, the PLL
locks onto the incoming signal and the KSZ8873MLL/FLL/RLL decodes a data frame. The receiver clock is maintained
active during idle periods in between data reception.
MDI/MDI-X Auto Crossover
To eliminate the need for crossover cables between similar devices, the KSZ8873MLL/FLL/RLL supports HP Auto
MDI/MDI-X and IEEE 802.3u standard MDI/MDI-X auto crossover. HP Auto MDI/MDI-X is the default.
The auto-sense function detects remote transmit and receive pairs and correctly assigns transmit and receive pairs for the
KSZ8873MLL/FLL/RLL device. This feature is extremely useful when end users are unaware of cable types, and also,
saves on an additional uplink configuration connection. The auto-crossover feature can be disabled through the port
control registers, or MIIM PHY registers.
相關PDF資料 |
PDF描述 |
|---|---|
| PIC16C54CT-04I/SO | IC MCU OTP 512X12 18SOIC |
| PIC12CE519T-04I/SN | IC MCU OTP 1KX12 W/EE 8SOIC |
| V300A8C400BG | CONVERTER MOD DC/DC 8V 400W |
| LTC1955IUH#PBF | IC SMART CARD INTERFACE DL 32QFN |
| V300A8C400BF3 | CONVERTER MOD DC/DC 8V 400W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8873MLL-EVAL | 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 1x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8873MLLI | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x RMII Interface (Industrial Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MLLJ | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x RMII Interface (Extended Temp) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MML | 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x MII Interface, Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8873MML-EVAL | 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 2x MII Interface - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
發布緊急采購，3分鐘左右您將得到回復。