- 您現在的位置：買賣IC網 > PDF目錄11573 > KSZ8842-16MVL (Micrel Inc)IC ETHERNET SW 2PORT BUS 128LQFP PDF資料下載
參數資料
| 型號： | KSZ8842-16MVL |
| 廠商： | Micrel Inc |
| 文件頁數： | 81/141頁 |
| 文件大小： | 0K |
| 描述： | IC ETHERNET SW 2PORT BUS 128LQFP |
| 標準包裝： | 90 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | PCI |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-LQFP |
| 供應商設備封裝： | 128-LQFP（14x14） |
| 包裝： | 托盤 |
| 產品目錄頁面： | 1081 (CN2011-ZH PDF) |
| 配用： | 576-1635-ND - BOARD EVALUATION KSZ8842-16MVL |
| 其它名稱： | 576-2119 KSZ8842-16MVL-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁當前第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁
Micrel, Inc.
KSZ8842-16/32 MQL/MVL/MVLI/MBL
October 2007
44
M9999-102207-1.9
Advanced Switch Functions
Spanning Tree Support
To support spanning tree, the host port is the designated port for the processor.
The other ports can be configured in one of the five spanning tree states via “transmit enable”, “receive enable” and
“l(fā)earning disable” register settings in registers P1CR2 and P2CR2 for ports 1 and 2, respectively. Table 9 shows the port
setting and software actions taken for each of the five spanning tree states.
Disable State
Port Setting
Software Action
The port should
not forward or
receive any
packets. Learning
is disabled.
“transmit
enable = 0,
receive
enable = 0,
learning
disable =1”
The processor should not send any packets to the port. The switch may still
send specific packets to the processor (packets that match some entries in
the “static MAC table” with “overriding bit” set) and the processor should
discard those packets. Address learning is disabled on the port in this
state.
Blocking State
Port Setting
Software Action
Only packets to
the processor are
forwarded.
“transmit
enable = 0,
receive
enable = 0,
learning
disable =1”
The processor should not send any packets to the port(s) in this state. The
processor should program the “Static MAC table” with the entries that it
needs to receive (for example, BPDU packets). The “overriding” bit should
also be set so that the switch will forward those specific packets to the
processor. Address learning is disabled on the port in this state.
Listening State
Port Setting
Software Action
Only packets to
and from the
processor are
forwarded.
Learning is
disabled.
“transmit
enable = 0,
receive
enable = 0,
learning
disable =1”
The processor should program the “Static MAC table” with the entries that it
needs to receive (for example, BPDU packets). The “overriding” bit should
be set so that the switch will forward those specific packets to the
processor. The processor may send packets to the port(s) in this state.
Address learning is disabled on the port in this state.
Learning State
Port Setting
Software Action
Only packets to
and from the
processor are
forwarded.
Learning is
enabled.
“transmit
enable = 0,
receive
enable = 0,
learning
disable = 0”
The processor should program the “Static MAC table” with the entries that it
needs to receive (for example, BPDU packets). The “overriding” bit should
be set so that the switch will forward those specific packets to the
processor. The processor may send packets to the port(s) in this state.
Address learning is enabled on the port in this state.
Forwarding
State
Port Setting
Software Action
Packets are
forwarded and
received normally.
Learning is
enabled.
“transmit
enable = 1,
receive enable
= 1, learning
disable = 0”
The processor programs the “Static MAC table” with the entries that it
needs to receive (for example, BPDU packets). The “overriding” bit is set so
that the switch forwards those specific packets to the processor. The
processor can send packets to the port(s) in this state. Address learning is
enabled on the port in this state.
Table 9. Spanning Tree States
相關PDF資料 |
PDF描述 |
|---|---|
| V300A12C400BL3 | CONVERTER MOD DC/DC 12V 400W |
| PIC16F687-E/P | IC PIC MCU FLASH 2KX14 20DIP |
| V300A12C400B3 | CONVERTER MOD DC/DC 12V 400W |
| V300A12C400B2 | CONVERTER MOD DC/DC 12V 400W |
| PIC16C505T-04E/SL | IC MCU OTP 1KX12 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8842-16MVL TR | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8842-16MVL-EVAL | 功能描述:BOARD EVALUATION KSZ8842-16MVL RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- 主要目的:電源管理，電池充電器 嵌入式:否 已用 IC / 零件:MAX8903A 主要屬性:1 芯鋰離子電池 次要屬性:狀態 LED 已供物品:板 |
| KSZ8842-16MVLI | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8842-16MVLI TR | 功能描述:以太網 IC 2-Port Ethernet Switch/Repeater + Generic (8, 16-bit) bus interface(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8842-32 | 制造商:MICREL 制造商全稱:Micrel Semiconductor 功能描述:2-Port Ethernet Switch with Non-PCI Interface |
發布緊急采購，3分鐘左右您將得到回復。