詳細信息
NC00001
PCB繼 電 器 | JQC-3FF |
●10A switching capability ●Small footprint ●Sealed type available ●Class B/F available ●Conform to RoHS,ELV directive |
■COIL DATA線圈參數（at 20℃）
Nominal Voltage額定電壓(VDC) | 3 | 5 | 6 | 9 | 12 | 18 | 24 | 48 | 0.36W |
Coil Resistance線圈阻值(Ω±10%) | 25 | 69 | 100 | 225 | 400 | 900 | 1600 | 6400 | |
Rated Current額定電流(mA) | 120 | 71.4 | 60 | 40 | 30 | 20 | 15 | 7.5 | |
Max Operate Voltage最大吸合電壓(VDC) | 2.25 | 3.75 | 4.5 | 6.75 | 9 | 13.5 | 18 | 36 | |
Min Release Voltage最小釋放電壓(VDC) | 0.15 | 0.25 | 0.3 | 0.45 | 0.6 | 0.9 | 1.2 | 2.4 | |
Max ApplicableVoltage最大過載電壓 | 70℃時額定電壓的130%，23℃時額定電壓的170% | ||||||||
■CONTACT DATA觸點參數
Contact Form觸點形式 | 1H/1Z |
Contact Material觸點材料 | Silver Alloy |
Load負載 | Resistive load(COSФ=1) |
Contact Ratings觸點負載 | 1H:10A 240VAC 1Z: 7A 240VAC 12A120VAC 10A120VAC |
Minimum load最小負載 | 100mA 5VDC |
Max Switching Voltage最大轉換電壓 | 250VAC/30VDC |
Max Switching Current最大轉換電流 | 15A |
Max Switching Power最大轉換功率 | 2770VA/240W |
Contact Resistance接觸電阻 | 100mΩMax at 6VDC 1A |
Life Expectancy壽命 | Electrical電氣壽命:100,000 Operations(at30Operations/minute) |
Mechanical機械壽命:10,000,000Operations(at300Operations/minute) |
■CHARACTERISTICS DATA性能參數
Insulation Resistance絕緣阻值 | 100MΩMinat 500VDC |
Dielectric Strength Between Open Contacts觸點間耐壓 | 750VAC(50/60Hz for one minute) |
Between Contacts and coil觸點與線圈間耐壓 | 1500VAC(50/60Hz for one minute) |
Operate Time吸合時間 | 10ms |
Release Time釋放時間 | 5ms |
Temperature Range環境溫度 | -40℃to+85℃ |
Shock Resistance沖擊 | Operating Extremes動作極限: 10G |
Damage Limits破壞極限: 100G | |
Vibration Resistance振動 | 10-55Hz, 1.5mm |
Max. switching frequency最大轉換頻率 | Mechanical: 18,000 operations/hr Electrical: 1,800 operations/hr |
Humidity濕度 | 40-85% |
Weight重量 | Approx 10g |
Safety Standard安全標準 | UL cUL TÜV CQC VDE |
■ENGINEERING DATA設計參數
■OVERALL AND MOUNTING DIMENSIONS安裝圖
REMARK（備注）：
1、產品部分外形尺寸中未注尺寸公差：當外形尺寸≤1mm時，公差為±0.2mm；當外形尺寸在1~5mm時，公差為±0.3mm；當外形尺寸＞5mm時，公差為±0.4mm。
2、安裝孔尺寸中未注尺寸公差均為±0.1mm。
聲明：
本產品規格書僅供客戶使用時參考，如有更改，恕不另行通知。