- 您現在的位置：買賣IC網 > PDF目錄92919 > AMMC-5620-W10 (AGILENT TECHNOLOGIES INC) 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER PDF資料下載
參數資料
| 型號： | AMMC-5620-W10 |
| 廠商： | AGILENT TECHNOLOGIES INC |
| 元件分類： | 放大器 |
| 英文描述： | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| 封裝： | 0.0555 X 0.0397 INCH, DIE |
| 文件頁數： | 6/8頁 |
| 文件大?。?/td> | 101K |
| 代理商： | AMMC-5620-W10 |
6
Biasing and Operation
The AMMC- 5620 is normally
biased with a single positive
drain supply connected to the
VDD bond pads shown in Figure
19. The recommended supply
voltage is 5 V, which results in
IDD = 95 mA (typical).
No ground wires are required
because all ground connections
are made with plated through-
holes to the backside of the
device.
Refer the Absolute Maximum
Ratings table for allowed DC
and thermal conditions.
Assembly Techniques
The backside of the AMMC- 5620
chip is RF ground. For
microstripline applications, the
chip should be attached directly
to the ground plane (e.g., circuit
carrier or heatsink) using
electrically conductive epoxy
[1].
For best performance, the
topside of the MMIC should be
brought up to the same height
as the circuit surrounding it.
This can be accomplished by
mounting a gold plated metal
shim (same length and width as
the MMIC) under the chip,
which is of the correct
thickness to make the chip and
adjacent circuit coplanar.
The amount of epoxy used for
chip and or shim attachment
should be just enough to
provide a thin fillet around the
bottom perimeter of the chip or
shim. The ground plane should
be free of any residue that may
jeopardize electrical or
mechanical attachment.
The location of the RF bond
pads is shown in Figure 20.
Note that all the RF input and
output ports are in a Ground-
Signal- Ground configuration.
RF connections should be kept
as short as reasonable to
minimize performance
degradation due to undesirable
series inductance. A single bond
wire is sufficient for signal
connections, however double-
bonding with 0.7 mil gold wire
or the use of gold mesh
[2] is
recommended for best
performance, especially near the
high end of the frequency range.
Thermosonic wedge bonding is
the preferred method for wire
attachment to the bond pads.
Gold mesh can be attached
using a 2 mil round tracking
tool and a tool force of
approximately 22 grams with an
ultrasonic power of roughly 55
dB for a duration of 76 ± 8 mS.
A guided wedge at an ultrasonic
power level of 64 dB can be
used for the 0.7 mil wire.
The
recommended wire bond stage
temperature is 150 ± 2
°C.
Caution should be taken to not
exceed the Absolute Maximum
Rating for assembly temperature
and time.
The chip is 100
m thick and
should be handled with care.
This MMIC has exposed air
bridges on the top surface and
should be handled by the edges
or with a custom collet (do not
pick up die with vacuum on die
center.)
This MMIC is also static
sensitive and ESD handling
precautions should be taken.
Notes:
1. Ablebond 84-1 LM1 silver epoxy is
recommended.
2. Buckbee-Mears Corporation, St. Paul, MN,
800-262-3824
相關PDF資料 |
PDF描述 |
|---|---|
| AMMC-5620-W50 | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMMC-5620-W10 | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMMC-5620-W50 | 6000 MHz - 20000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| AMMC-6120-W50 | 8000 MHz - 20000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| AMMC-6140-W10 | 10000 MHz - 20000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMMC-5620-W50 | 功能描述:射頻放大器 Amp GaAs MMIC RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| AMMC-6 | 功能描述:接線端子工具和配件 END CLMP F. TERM MOD RoHS:否 制造商:Phoenix Contact 產品:Tools & Accessories 類型:End Bracket |
| AMMC-6120-W10 | 功能描述:射頻放大器 Doubler MMIC 6-20GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| AMMC-6120-W50 | 功能描述:射頻放大器 Doubler MMIC 6-20GHz RoHS:否 制造商:Skyworks Solutions, Inc. 類型:Low Noise Amplifier 工作頻率:2.3 GHz to 2.8 GHz P1dB:18.5 dBm 輸出截獲點:37.5 dBm 功率增益類型:32 dB 噪聲系數:0.85 dB 工作電源電壓:5 V 電源電流:125 mA 測試頻率:2.6 GHz 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 封裝:Reel |
| AMMC-6140-W10 | 功能描述:射頻無線雜項 Doubler MMIC 6-40GHz RoHS:否 制造商:Texas Instruments 工作頻率:112 kHz to 205 kHz 電源電壓-最大:3.6 V 電源電壓-最小:3 V 電源電流:8 mA 最大功率耗散: 工作溫度范圍:- 40 C to + 110 C 封裝 / 箱體:VQFN-48 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。